Airlink AML001 Manual - Page 38

X<value> Commands, Command, Description, Appendix

Get Airlink AML001 PDF manuals and user guides View all Airlink AML001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Appendix A AT Commands parameter of this command is stored in bits 4-6 of register S22. X Commands Command Description X0 Busy detection is disabled; blind dialing (no dial tone detection) is enabled. The following result codes are supported: • OK • CONNECT • RING • NO CARRIER •  ERROR X1 Busy detection is disabled; blind dialing (no dial tone detection) is enabled. The following result codes are supported: • OK • RING • NO CARRIER • ERROR • CONNECT X2 Busy detection is disabled; blind dialing is disabled. The dialing cannot be conducted unless a dial tone is detected. If dial tone is not detected within the time specified by register S6, the NO DIAL-TONE result code will be reported. The following result codes are supported: • OK • RING • NO CARRIER • ERROR • NO DIALTONE • CONNECT X3 Busy detection is enabled; blind dialing is enabled. The following result codes are supported: • OK • RING • NO CARRIER • ERROR • BUSY • CONNECT • BLACKLISTED X4 Busy detection is enabled; blind dialing is disabled. The dialing cannot be conducted unless a dial tone is detected. If dial tone is not detected within the time specified by register S6, the NO DIAL-TONE result code will be reported. The following result codes are supported: • OK • RING • NO CARRIER • ERROR • NO DIALTONE • BUSY • CONNECT • DELAYED • BLACKLISTED • WARBLE 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Appendix A
AT Commands
37
parameter of this command is stored in bits 4°6 of register S22.
X<value> Commands
Command
Description
X0
Busy detection is disabled; blind dialing (no dial tone
detection) is enabled. The following result codes are supported:
•
OK
•
CONNECT
•
RING
•
NO CARRIER
•
ERROR
X1
Busy detection is disabled; blind dialing (no dial tone
detection) is enabled. The following result codes are supported:
•
OK
•
RING
•
NO CARRIER
•
ERROR
•
CONNECT <RATE>
X2
Busy detection is disabled; blind dialing is disabled. The
dialing cannot be conducted unless a dial tone is detected. If
dial tone is not detected within the time specified by register
S6, the NO DIAL-TONE result code will be reported. The
following result codes are supported:
•
OK
•
RING
•
NO CARRIER
•
ERROR
•
NO DIALTONE
•
CONNECT <RATE>
X3
Busy detection is enabled; blind dialing is enabled. The
following result codes are supported:
•
OK
•
RING
•
NO CARRIER
•
ERROR
•
BUSY
•
CONNECT <RATE>
•
BLACKLISTED
X4
Busy detection is enabled; blind dialing is disabled. The
dialing cannot be conducted unless a dial tone is detected. If
dial tone is not detected within the time specified by register
S6, the NO DIAL-TONE result code will be reported. The
following result codes are supported:
•
OK
•
RING
•
NO CARRIER
•
ERROR
•
NO DIALTONE
•
BUSY
•
CONNECT <RATE>
•
DELAYED
•
BLACKLISTED
•
WARBLE