Airlink AML001 Manual - Page 60

Disable caller ID., FTH=<mod&gt

Get Airlink AML001 PDF manuals and user guides View all Airlink AML001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Appendix A AT Commands +PMHT=6 Grant modem on hold request with a 2 min. time-out. +PMHT=7 Grant modem on hold request with a 3 min. time-out. +PMHT=8 Grant modem on hold request with a 4 min. time-out. +PMHT=9 Grant modem on hold request with a 6 min. time-out. +PMHT=10 Grant modem on hold request with a 8 min. time-out. +PMHT=11 Grant modem on hold request with a 12 min. time-out. +PMHT=12 Grant modem on hold request with a 16 min. time-out. +PMHT=13 Grant modem on hold request with an indefinite time-out. +PQC=-V.92 Phase 1 and Phase 2 Control Use this command to configure the V.92 short training sequence. This command selects which short phases are used during initiation of a connection. Once the modem is configured, use the +PSS command to enable or disable the short training sequence. +PQC=0 +PQC=1 +PQC=2 +PQC=3 Enable short phase 1 and short phase 2 (default). Enable short phase 1 only. Enable short phase 2 only. Disable short phase 1 and short phase 2. +PSS=-Use Short Sequence Use this command to enable or disable the V.92 short training sequence. +PSS=0 +PSS=2 Use training sequence set in by the +PQC command. Use long training sequence. +VCID=-Caller ID Use this command to enable or disable caller ID. +VCID=0 +VCID=1 +VCID=2 Disable caller ID. Enable caller ID with formatted presentation. Enable caller ID with out formatting. +FTH=-Transmit HDLC Data with Carrier The +FTH= command causes the modem to transmit data framed in the HDLC protocol. +FTH=3 +FTH=24 +FTH=48 +FTH=72 V.21 channel 2. 300 bits/s. V.27ter. 2400 bits/s. V.27ter. 4800 bits/s. V.29. 7200 bits/s. 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Appendix A
AT Commands
59
+PMHT=6
Grant modem on hold request with a 2 min. time-out.
+PMHT=7
Grant modem on hold request with a 3 min. time-out.
+PMHT=8
Grant modem on hold request with a 4 min. time-out.
+PMHT=9
Grant modem on hold request with a 6 min. time-out.
+PMHT=10
Grant modem on hold request with a 8 min. time-out.
+PMHT=11
Grant modem on hold request with a 12 min. time-out.
+PMHT=12
Grant modem on hold request with a 16 min. time-out.
+PMHT=13
Grant modem on hold request with an indefinite time-out.
+PQC=<value>±V.92 Phase 1 and Phase 2 Control
Use this command to configure the V.92 short training sequence. This
command selects which short phases are used during initiation of a
connection. Once the modem is configured, use the
+PSS
command to
enable or disable the short training sequence.
+PQC=0
Enable short phase 1 and short phase 2 (default).
+PQC=1
Enable short phase 1 only.
+PQC=2
Enable short phase 2 only.
+PQC=3
Disable short phase 1 and short phase 2.
+PSS=<value>±Use Short Sequence
Use this command to enable or disable the V.92 short training sequence.
+PSS=0
Use training sequence set in by the
+PQC
command.
+PSS=2
Use long training sequence.
+VCID=<value>±Caller ID
Use this command to enable or disable caller ID.
+VCID=0
Disable caller ID.
+VCID=1
Enable caller ID with formatted presentation.
+VCID=2
Enable caller ID with out formatting.
+FTH=<mod>±Transmit HDLC Data with <mod> Carrier
The
+FTH=<mod>
command causes the modem to transmit data framed in
the HDLC protocol.
+FTH=3
V.21 channel 2. 300 bits/s.
+FTH=24
V.27ter. 2400 bits/s.
+FTH=48
V.27ter. 4800 bits/s.
+FTH=72
V.29. 7200 bits/s.