Airlink AML001 Manual - Page 43

N<value&gt, When Modem Is Operating in Data Transfer Mode, K0, \K2, K4

Get Airlink AML001 PDF manuals and user guides View all Airlink AML001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

PCI Modem Card User's Manual \A-Select Maximum MNP Block Size The modem will operate an MNP error corrected link using a maximum block size controlled by the parameter sup-plied. \A0 64 characters. \A1 128 characters. \A2 192 characters. \A3 256 characters (default). \B-Send Break Use this command in non-error-controlled mode. It instructs the modem to transmit a break signal to the remote modem. The minimum break length is 100 ms and the maximum break length is 900 ms. The parameter has values between one and nine with each increment representing 100 ms. The command works in conjunction with the \K command. \G-Modem Port Flow Control Instructs the DCE to process XON/XOFF flow control or pass XON/OFF flow control to the remote DCE. \G0 The modem processes XON/XOFF flow control characters locally (default). \G1 The modem passes XON/XOFF flow control characters. \J-Adjust Bits/s Rate Control Use this command to specify whether or not the negotiated connect speed of the modem forces the adjustment of the speed of the DTE to the modem's speed. \J0 Buffer mode. Error control is set or disabled with the \N command (default). \J1 Forces the maximum DCE rate to the DTE rate. \K-Set Break Control Use this command to control the response of the modem to a break received from the DTE, remote modem, or the \B command. When Modem Is Operating in Data Transfer Mode: \K0, \K2, K4 Enter on-line command mode. No break is sent to the remote modem. \K1 Clears data buffers and sends a break to the remote modem. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
PCI Modem Card User’s Manual
42
\A<value>±Select Maximum MNP Block Size
The modem will operate an MNP error corrected link using a maximum
block size controlled by the parameter sup-plied.
\A0
64 characters.
\A1
128 characters.
\A2
192 characters.
\A3
256 characters (default).
\B<break time>±Send Break
Use this command in non-error-controlled mode. It instructs the modem to
transmit a break signal to the remote modem. The minimum break length is
100 ms and the maximum break length is 900 ms. The <break time>
parameter has values between one and nine with each increment representing
100 ms. The command works in conjunction with the
\K
command.
\G<value>±Modem Port Flow Control
Instructs the DCE to process XON/XOFF flow control or pass XON/OFF
flow control to the remote DCE.
\G0
The modem processes XON/XOFF flow control characters
locally (default).
\G1
The modem passes XON/XOFF flow control characters.
\J<value>±Adjust Bits/s Rate Control
Use this command to specify whether or not the negotiated connect speed of
the modem forces the adjustment of the speed of the DTE to the modem±s
speed.
\J0
Buffer mode. Error control is set or disabled with the
\N<value>
command (default).
\J1
Forces the maximum DCE rate to the DTE rate.
\K<value>±Set Break Control
Use this command to control the response of the modem to a break received
from the DTE, remote modem, or the
\B<value>
command.
When Modem Is Operating in Data Transfer Mode:
\K0, \K2, K4
Enter on-line command mode. No break is sent to the remote
modem.
\K1
Clears data buffers and sends a break to the remote modem.