Airlink AML001 Manual - Page 41

Enables XON/XOFF flow control., N<error control mode&gt

Get Airlink AML001 PDF manuals and user guides View all Airlink AML001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

PCI Modem Card User's Manual &K0 &K3 &K4 Disables flow control. Enables RTS/CTS (hardware) flow control (default). Enables XON/XOFF flow control. &M-Asynchronous Communications Mode This command is supported to ensure compatibility with communication software that issues the &M0 command. The preferred method for changing the asynchronous communication mode is to use the \N command. &M0 Asynchronous mode (default). &P-Pulse Dial Make-to-Break Ratio Selection This command is effective only for Japan. &P0 Selects 39%-61% make/break ratio at 10 pulses per second. &P1 Selects 33%-67% make/break ratio at 10 pulses per second (default). &P2 Selects 33%-67% make/break ratio at 20 pulses per second. &Q-Asynchronous Communications Mode This command is supported to ensure compatibility with communication software that issues the &Q command. The preferred method for changing the asynchronous communication mode is to use the \N command. &Q0 &Q5 &Q6 &Q8 &Q9 Asynchronous mode, buffered. Same as \N0. Error control mode, buffered (default). Same as \N3. Asynchronous mode, buffered. Same as \N0. MNP error control mode. If an MNP error control protocol is not established, the modem will fall back according to the current user setting in register S36. V. 4 2 o r MNP error control mode. If neither error control protocol is established, the modem will fall back according to the current user setting in register S36. &S-Data Set Ready (DSR) Option Use this command to controls DSR action. &S0 DSR is always on (default). 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
PCI Modem Card User’s Manual
40
&K0
Disables flow control.
&K3
Enables RTS/CTS (hardware) flow control (default).
&K4
Enables XON/XOFF flow control.
&M<value>±Asynchronous Communications Mode
This command is supported to ensure compatibility with communication
software that issues the
&M0
command.
The preferred method for changing the asynchronous communication mode
is to use the
\N<error control mode>
command.
&M0
Asynchronous mode (default).
&P<value>±Pulse Dial Make-to-Break Ratio Selection
This command is effective only for Japan.
&P0
Selects 39%°61% make/break ratio at 10 pulses per second.
&P1
Selects 33%°67% make/break ratio at 10 pulses per second
(default).
&P2
Selects 33%°67% make/break ratio at 20 pulses per second.
&Q<value>±Asynchronous Communications Mode
This command is supported to ensure compatibility with communication
software that issues the
&Q<value>
command.
The preferred method for changing the asynchronous communication mode
is to use the
\N<error control mode>
command.
&Q0
Asynchronous mode, buffered. Same as
\N
0.
&Q5
Error control mode, buffered (default). Same as
\N
3.
&Q6
Asynchronous mode, buffered. Same as
\N
0.
&Q8
MNP error control mode. If an MNP error control protocol is
not established, the modem will fall back according to the
current user setting in register S36.
&Q9
V. 4 2 o r MNP error control mode. If neither error control
protocol is established, the modem will fall back according to
the current user setting in register S36.
&S<value>±Data Set Ready (DSR) Option
Use this command to controls DSR action.
&S0
DSR is always on (default).