Cisco 3750G-12S Hardware Installation Guide - Page 122

Wiring the DC-Input Power Source

Get Cisco 3750G-12S - Catalyst Switch - Stackable PDF manuals and user guides
UPC - 746320812526
View all Cisco 3750G-12S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

Connecting to DC Power Appendix C Connecting to DC Power Wiring the DC-Input Power Source Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003 Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 5 A Statement 1005 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Caution You must connect the Catalyst 3750G-12S-SD switch only to a DC-input power source that has an input supply voltage from -36 to -72 VDC. If the supply voltage is not in this range, the switch might not operate properly or might be damaged. Caution The switch must be installed with 5 A-branch-circuit protection. Note This installation must comply with all applicable codes. To wire the switch to a DC-input power source, follow these steps: Step 1 Apply tape to the circuit-breaker switch handle, and move the circuit-breaker handle to the off position. Step 2 Locate and remove the terminal block plug (see Figure C-4). Figure C-4 Terminal Block Plug 60530 Catalyst 3750 Switch Hardware Installation Guide C-4 OL-6336-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
C-4
Catalyst 3750 Switch Hardware Installation Guide
OL-6336-10
Appendix C
Connecting to DC Power
Connecting to DC Power
Wiring the DC-Input Power Source
Warning
Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 5 A
Statement 1005
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Caution
You must connect the Catalyst 3750G-12S-SD switch only to a DC-input power source that has an input
supply voltage from –36 to –72 VDC. If the supply voltage is not in this range, the switch might not
operate properly or might be damaged.
Caution
The switch must be installed with 5 A-branch-circuit protection.
Note
This installation must comply with all applicable codes.
To wire the switch to a DC-input power source, follow these steps:
Step 1
Apply tape to the circuit-breaker switch handle, and move the circuit-breaker handle to the off position.
Step 2
Locate and remove the terminal block plug (see
Figure C-4
).
Figure C-4
Terminal Block Plug
60530