Cisco 3750G-12S Hardware Installation Guide - Page 63

Mounting the Catalyst 3750G-24WS-S25 and 3750G-24WS-S50 Switches in a Rack - 12 port

Get Cisco 3750G-12S - Catalyst Switch - Stackable PDF manuals and user guides
UPC - 746320812526
View all Cisco 3750G-12S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

141734 Chapter 2 Switch Installation Installing the Switch Figure 2-37 Mounting the Catalyst 3750G-24WS-S25 and 3750G-24WS-S50 Switches in a Rack SYST RPS MASTR STAT DUPLX SPEED STACK PoE 1 12 1X 34 56 78 9 10 11 12 11X 2X 12X 13 14 13X 15 16 17 18 19 20 21 22 23 24 23X 14X 24X CataWlyirset l3e7ss50LGASNERCIESoPntorEol-l2e4r 25 26 1 Phillips machine screws After you mount the switch in the rack, you might need to perform these tasks to complete the installation, to run the setup program, and to access the switch: • (Optional) Connect the switches in the stacks. See the "Connecting StackWise Cable to StackWise Ports" section on page 2-30. • Power on the switch. See the "Verifying Switch Operation" section on page 2-7. If the switches are stacked, see the "Planning Considerations" section on page 2-8 for information on powering considerations. • Connect to a 10/100 or 10/100/1000 port and run Express Setup. See the Catalyst 3750 Switch Getting Started Guide for instructions. • Connect to the front-panel ports. See the "Connecting to the 10/100 and 10/100/1000 Ports" section on page 2-39 and the "Connecting to an SFP Module" section on page 2-41 to complete the installation. For configuration instructions about using the CLI setup program, go to Appendix D, "Configuring the Switch with the CLI-Based Setup Program." To use the CLI, enter commands at the Switch> prompt through the console port by using a terminal program or through the network by using Telnet. For configuration information, see the switch software configuration guide or the switch command reference. OL-6336-10 Catalyst 3750 Switch Hardware Installation Guide 2-25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
2-25
Catalyst 3750 Switch Hardware Installation Guide
OL-6336-10
Chapter 2
Switch Installation
Installing the Switch
Figure 2-37
Mounting the Catalyst 3750G-24WS-S25 and 3750G-24WS-S50 Switches in a Rack
After you mount the switch in the rack, you might need to perform these tasks to complete the
installation, to run the setup program, and to access the switch:
•
(Optional) Connect the switches in the stacks. See the
“Connecting StackWise Cable to StackWise
Ports” section on page 2-30
.
•
Power on the switch. See the
“Verifying Switch Operation” section on page 2-7
. If the switches are
stacked, see the
“Planning Considerations” section on page 2-8
for information on powering
considerations.
•
Connect to a 10/100 or 10/100/1000 port and run Express Setup. See the
Catalyst 3750 Switch
Getting Started Guide
for instructions.
•
Connect to the front-panel ports. See the
“Connecting to the 10/100 and 10/100/1000 Ports” section
on page 2-39
and the
“Connecting to an SFP Module” section on page 2-41
to complete the
installation.
For configuration instructions about using the CLI setup program, go to
Appendix D, “Configuring the
Switch with the CLI-Based Setup Program.”
To use the CLI, enter commands at the
Switch
> prompt through the console port by using a terminal
program or through the network by using Telnet. For configuration information, see the switch software
configuration guide or the switch command reference.
1
Phillips machine screws
Catalyst 3750G
SERIES
PoE-24
Wireless LAN Controller
SYST
RPS
MASTR
STAT
DUPLX
SPEED
STACK
PoE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
141734
1