Cisco 3750G-12S Hardware Installation Guide - Page 79

Connecting to an SFP Module, Connecting to a Fiber-Optic SFP Module

Get Cisco 3750G-12S - Catalyst Switch - Stackable PDF manuals and user guides
UPC - 746320812526
View all Cisco 3750G-12S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Chapter 2 Switch Installation Connecting to an SFP Module Step 2 Step 3 Step 4 Connect the other end of the cable to an RJ-45 connector on the other device. The port LED turns on when both the switch and the connected device have established link. The port LED is amber while Spanning Tree Protocol (STP) discovers the topology and searches for loops. This process takes about 30 seconds, and then the port LED turns green. If the port LED does not turn on, the device at the other end might not be turned on, or there might be a cable problem or a problem with the adapter installed in the attached device. See Chapter 3, "Troubleshooting," for solutions to cabling problems. Reconfigure and reboot the connected device if necessary. Repeat Steps 1 through 3 to connect each device. Figure 2-55 Connecting to an Ethernet Port SYST RPS MASTR STAT DUPLX SPEED STACK MODE 12 1X 34 56 78 9 10 11 12 11X 2X 12X 86818 Connecting to an SFP Module This section describes how to connect to SFP modules. • For instructions on how to connect to fiber-optic SFP modules, see the "Connecting to 1000BASE-T SFP Modules" section. • For instructions on how to connect to 1000BASE-T SFP modules, see the "Connecting to 1000BASE-T SFP Modules" section. • For instructions on how to install or remove an SFP module, see the "Installing and Removing SFP Modules" section on page 2-33. Connecting to a Fiber-Optic SFP Module Follow these steps to connect a fiber-optic cable to an SFP module: Warning Class 1 laser product. Statement 1008 OL-6336-10 Catalyst 3750 Switch Hardware Installation Guide 2-41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
2-41
Catalyst 3750 Switch Hardware Installation Guide
OL-6336-10
Chapter 2
Switch Installation
Connecting to an SFP Module
Step 2
Connect the other end of the cable to an RJ-45 connector on the other device. The port LED turns on
when both the switch and the connected device have established link.
The port LED is amber while Spanning Tree Protocol (STP) discovers the topology and searches for
loops. This process takes about 30 seconds, and then the port LED turns green. If the port LED does not
turn on, the device at the other end might not be turned on, or there might be a cable problem or a
problem with the adapter installed in the attached device. See
Chapter 3, “Troubleshooting,”
for
solutions to cabling problems.
Step 3
Reconfigure and reboot the connected device if necessary.
Step 4
Repeat Steps 1 through 3 to connect each device.
Figure 2-55
Connecting to an Ethernet Port
Connecting to an SFP Module
This section describes how to connect to SFP modules.
•
For instructions on how to connect to fiber-optic SFP modules, see the
“Connecting to 1000BASE-T
SFP Modules”
section.
•
For instructions on how to connect to 1000BASE-T SFP modules, see the
“Connecting to
1000BASE-T SFP Modules”
section.
•
For instructions on how to install or remove an SFP module, see the
“Installing and Removing SFP
Modules” section on page 2-33
.
Connecting to a Fiber-Optic SFP Module
Follow these steps to connect a fiber-optic cable to an SFP module:
Warning
Class 1 laser product.
Statement 1008
SYST
RPS
MASTR
STAT
DUPLX
SPEED
STACK
MODE
1X
2X
11X
12X
1
2
3
4
5
6
7
8
9
10
11
12
86818