Cisco 3750G-12S Hardware Installation Guide - Page 23

SFP Modules, XENPAK Module Slot (Catalyst 3750G-16TD Switch), LEDs - used

Get Cisco 3750G-12S - Catalyst Switch - Stackable PDF manuals and user guides
UPC - 746320812526
View all Cisco 3750G-12S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Chapter 1 Product Overview 10/100 and 10/100/1000 Ports SFP Modules The Catalyst 3750 switch uses Gigabit Ethernet SFP modules to establish connections to other devices. These transceiver modules are field-replaceable, providing the uplink interfaces when inserted in an SFP module slot. You can use the SFP modules for Gigabit uplink connections to other switches. You use fiber-optic cables with LC or MT-RJ connectors to connect to a fiber-optic SFP module. You use a Category 5 or higher cable with RJ-45 connectors to connect to a copper SFP module. For more information about these SFP modules, see your SFP module documentation. XENPAK Module Slot (Catalyst 3750G-16TD Switch) The Catalyst 3750G-16TD switch uses 10-Gigabit Ethernet XENPAK modules to establish connections to networks. You install the modules in the module slot in the switch front panel. See Table B-2 on page B-4 for a list of XENPAK modules that the Catalyst 3750G-16TD switch supports. Note The 10-Gigabit Ethernet XENPAK modules are referred to as 10-Gigabit Ethernet module ports in the software documentation. LEDs You can use the switch LEDs to monitor switch activity and its performance. Figure 1-16, Figure 1-17, and Figure 1-18 show the switch LEDs and the Mode button that you use to select one of the port modes. All LEDs are visible through the GUI management applications-the Network Assistant application for multiple switches and the device manager GUI for a single switch. The switch software configuration guide describes how to use the command-line interface (CLI) to configure and monitor individual switches and switch clusters. OL-6336-10 Catalyst 3750 Switch Hardware Installation Guide 1-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
1-13
Catalyst 3750 Switch Hardware Installation Guide
OL-6336-10
Chapter 1
Product Overview
10/100 and 10/100/1000 Ports
SFP Modules
The Catalyst 3750 switch uses Gigabit Ethernet SFP modules to establish connections to other devices.
These transceiver modules are field-replaceable, providing the uplink interfaces when inserted in an SFP
module slot. You can use the SFP modules for Gigabit uplink connections to other switches. You use
fiber-optic cables with LC or MT-RJ connectors to connect to a fiber-optic SFP module. You use a
Category 5 or higher cable with RJ-45 connectors to connect to a copper SFP module.
For more information about these SFP modules, see your SFP module documentation.
XENPAK Module Slot (Catalyst 3750G-16TD Switch)
The Catalyst 3750G-16TD switch uses 10-Gigabit Ethernet XENPAK modules to establish connections
to networks. You install the modules in the module slot in the switch front panel. See
Table B-2 on
page B-4
for a list of XENPAK modules that the Catalyst 3750G-16TD switch supports.
Note
The 10-Gigabit Ethernet XENPAK modules are referred to as 10-Gigabit Ethernet module ports in the
software documentation.
LEDs
You can use the switch LEDs to monitor switch activity and its performance.
Figure 1-16
,
Figure 1-17
,
and
Figure 1-18
show the switch LEDs and the Mode button that you use to select one of the port modes.
All LEDs are visible through the GUI management applications—the Network Assistant application for
multiple switches and the device manager GUI for a single switch. The switch software configuration
guide describes how to use the command-line interface (CLI) to configure and monitor individual
switches and switch clusters.