Home » Cisco Manuals » Hubs & Switches » Cisco 3750G-12S » Manual Viewer

Cisco 3750G-12S Hardware Installation Guide - Page 73

Installing and Removing XENPAK Modules (Catalyst 3750G-16TD Switch - - 12 sfp

UPC - 746320812526

Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Chapter 2 Switch Installation Installing and Removing XENPAK Modules (Catalyst 3750G-16TD Switch) Step 3 Unlock and remove the SFP module, as shown in Figure 2-49. If the module has a bale-clasp latch, pull the bale out and down to eject the module. If the bale-clasp latch is obstructed and you cannot use your index finger to open it, use a small, flat-blade screwdriver or other long, narrow instrument to open the bale-clasp latch. Figure 2-49 Removing a Bale-Clasp Latch SFP Module by Using a Flat-Blade Screwdriver 86554 13 X 14 15 16 17 18 19 20 21 22 23 24 23X X 24X Catalyst 3750 SERIES 1 2 1 1 Bale clasp Warning When the Catalyst 3750-12S switch and 100BASE-FX MMF small form-factor pluggable (SFP) module (model number GLC-GE-100FX) are running, the surface temperature of the removed SFP module might be hot. Statement 377 Step 4 Step 5 Step 6 Grasp the SFP module between your thumb and index finger, and carefully remove it from the module slot. For fiber-optic SFP modules, insert a dust plug into the optical ports of the SFP module to keep the optical interfaces clean. Place the removed SFP module in an antistatic bag or other protective environment. Installing and Removing XENPAK Modules (Catalyst 3750G-16TD Switch) These sections describe how to install and remove XENPAK modules: • Removing SFP Modules from SFP Module Slots, page 2-34 • Removing a XENPAK Module, page 2-38 XENPAK modules are inserted into the XENPAK module slot on the front panel of the Catalyst 3750G-16TD switch. These field-replaceable transceiver modules provide 10-Gigabit interfaces. OL-6336-10 Catalyst 3750 Switch Hardware Installation Guide 2-35

Section	Page
Catalyst 3750 Switch Hardware Installation Guide	1
Preface	7
Audience	7
Purpose	7
Conventions	7
Related Publications	8
Obtaining Documentation, Obtaining Support, and Security Guidelines	9
Product Overview	11
Features	11
Front Panel Description	13
Fast Ethernet Switches	13
Catalyst 3750-24FS and 3750V2-24FS Switch Front Panel	13
Catalyst 3750-24TS and 3750V2-24TS Switch Front Panel	14
Catalyst 3750-48TS and 3750V2-48TS Switch Front Panel	15
Catalyst 3750-24PS and 3750V2-24PS Switch Front Panel	15
Catalyst 3750-48PS and 3750V2-48PS Switch Front Panel	16
Gigabit Ethernet Switches	16
Catalyst 3750G-12S and Catalyst 3750G-12S-SD Switch Front Panel	16
Catalyst 3750-24T, 3750G-24TS, and 3750G-24TS-1U Switch Front Panel	16
Catalyst 3750G-48TS Switch Front Panel	18
Catalyst 3750G-24PS Switch Front Panel	18
Catalyst 3750G-48PS Switch Front Panel	19
Catalyst 3750G-16TD Switch Front Panel	19
Catalyst 3750G Integrated Wireless LAN Controller Switch Front Panel	20
10/100 and 10/100/1000 Ports	20
100BASE-FX Ports	22
SFP Module Slots	22
SFP Modules	23
XENPAK Module Slot (Catalyst 3750G-16TD Switch)	23
LEDs	23
System LED	25
RPS LED	26
Master LED	26
Port LEDs and Modes	27
Rear Panel Description	31
StackWise Ports	34
Power Connectors	35
Internal Power Supply Connector	35
DC Power Connector	35
Cisco RPS Connector	35
Console Port	36
Management Options	36
Network Configurations	37
Switch Installation	39
Preparing for Installation	39
Warnings	40
Installation Guidelines	44
Box Contents	45
Tools and Equipment	45
Verifying Switch Operation	45
Powering On the Switch and Running POST	45
Powering Off the Switch	46
Planning the Stack	46
Planning Considerations	46
Powering Considerations	46
Cabling Considerations	47
Recommended Cabling Configurations	48
Installing the Switch	49
Rack-Mounting	50
Removing Screws from the Switch	50
Attaching Brackets to the Catalyst 3750G-24TS Switch	52
Attaching Brackets to the Catalyst 3750G Integrated Wireless LAN Controller Switches	55
Attaching Brackets to All Other Catalyst 3750 Switches	56
Mounting the Switch in a Rack	62
Attaching the Cable Guide	64
Wall-Mounting	65
Attaching the Brackets to the Switch for Wall-Mounting	66
Attaching the RPS Connector Cover	66
Mounting the Switch on a Wall	67
Table- or Shelf-Mounting	68
Connecting StackWise Cable to StackWise Ports	68
Installing and Removing SFP Modules	71
Installing SFP Modules into SFP Module Slots	71
Removing SFP Modules from SFP Module Slots	72
Installing and Removing XENPAK Modules (Catalyst 3750G-16TD Switch)	73
Installing a XENPAK Module	74
Removing a XENPAK Module	76
Connecting to the 10/100 and 10/100/1000 Ports	77
Connecting to an SFP Module	79
Connecting to a Fiber-Optic SFP Module	79
Connecting to 1000BASE-T SFP Modules	81
Connecting to a XENPAK Module	82
Where to Go Next	83
Troubleshooting	85
Diagnosing Problems	85
Verify Switch POST Results	86
Monitor Switch LEDs	86
Verify Switch Connections	86
Bad or Damaged Cable	86
Ethernet and Fiber Cables	86
Link Status	87
PoE Connections	87
Transceiver Module Port Issues	87
Port and Interface Settings	88
Ping the End Device	88
Spanning Tree Loops	88
Monitor Switch Performance	89
Speed, Duplex, and Autonegotiation	89
Autonegotiation and NIC Cards	89
Cabling Distance	89
Clearing the Switch IP Address and Configuration	90
Replacing a Failed Stack Member	90
Finding the Switch Serial Number	91
Technical Specifications	97
Connector and Cable Specifications	109
Connector Specifications	109
10/100 and 10/100/1000 Ports	110
100BASE-FX Ports	110
SFP Module Ports	111
XENPAK Module Ports (Catalyst 3750G-16TD Switch)	112
Console Port	112
Cable and Adapter Specifications	113
SFP Module Cable Specifications	113
Two Twisted-Pair Cable Pinouts	114
Four Twisted-Pair Cable Pinouts for 10/100 Ports	115
Identifying a Crossover Cable	116
Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports	116
Crossover Cable and Adapter Pinouts	117
Connecting to DC Power	119
Connecting to DC Power	119
Preparing for Installation	119
Grounding the Switch	120
Wiring the DC-Input Power Source	122
Configuring the Switch with the CLI-Based Setup Program	127
Accessing the CLI	128
Accessing the CLI Through Express Setup	128
Accessing the CLI Through the Console Port	128
Taking Out What You Need	129
Stacking the Switches (Optional)	130
Connecting to the Console Port	131
Starting the Terminal Emulation Software	132
Connecting to a Power Source	132
Entering the Initial Configuration Information	133
IP Settings	133

Match case Limit results 1 per page

2-35

Catalyst 3750 Switch Hardware Installation Guide

OL-6336-10

Chapter 2

Switch Installation

Installing and Removing XENPAK Modules (Catalyst 3750G-16TD Switch)

Step 3

Unlock and remove the SFP module, as shown in

Figure 2-49

If the module has a bale-clasp latch, pull the bale out and down to eject the module. If the bale-clasp

latch is obstructed and you cannot use your index finger to open it, use a small, flat-blade screwdriver

or other long, narrow instrument to open the bale-clasp latch.

Figure 2-49

Removing a Bale-Clasp Latch SFP Module by Using a Flat-Blade Screwdriver

Warning

When the Catalyst 3750-12S switch and 100BASE-FX MMF small form-factor pluggable (SFP) module

(model number GLC-GE-100FX) are running, the surface temperature of the removed SFP module might

be hot.

Statement 377

Step 4

Grasp the SFP module between your thumb and index finger, and carefully remove it from the

module slot.

Step 5

For fiber-optic SFP modules, insert a dust plug into the optical ports of the SFP module to keep the

optical interfaces clean.

Step 6

Place the removed SFP module in an antistatic bag or other protective environment.

Installing and Removing XENPAK Modules

(Catalyst 3750G-16TD Switch)

These sections describe how to install and remove XENPAK modules:

•

Removing SFP Modules from SFP Module Slots, page 2-34

•

Removing a XENPAK Module, page 2-38

XENPAK modules are inserted into the XENPAK module slot on the front panel of the Catalyst

3750G-16TD switch. These field-replaceable transceiver modules provide 10-Gigabit interfaces.

Bale clasp

Catalyst 3750

SERIES

23X

24X

86554