Home » Cisco Manuals » Hubs & Switches » Cisco 3750G-12S » Manual Viewer

Cisco 3750G-12S Hardware Installation Guide - Page 68

Table- or Shelf-Mounting, Connecting StackWise Cable to StackWise Ports

UPC - 746320812526

Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Connecting StackWise Cable to StackWise Ports Chapter 2 Switch Installation • Connect to the front-panel ports. See the "Connecting to the 10/100 and 10/100/1000 Ports" section on page 2-39 and the "Connecting to an SFP Module" section on page 2-41 to complete the installation. For configuration instructions about using the CLI setup program, go to Appendix D, "Configuring the Switch with the CLI-Based Setup Program." To use the CLI, enter commands at the Switch> prompt through the console port by using a terminal program or through the network by using Telnet. For configuration information, see the switch software configuration guide or the switch command reference. Table- or Shelf-Mounting Follow these steps to install the switch on a table or shelf: Step 1 Step 2 Locate the adhesive strip with the rubber feet in the mounting-kit envelope. Attach the four rubber feet to the recessed areas on the bottom of the unit. Place the switch on the table or shelf near an AC power source. After the switch is mounted on the table, you might need to perform these tasks to complete the installation, run the setup program, and access the switch: • (Optional) Connect the switches in the stacks. See the "Connecting StackWise Cable to StackWise Ports" section on page 2-30. • Power on the switch. See the "Verifying Switch Operation" section on page 2-7. If the switches are stacked, see the "Planning Considerations" section on page 2-8 for information on powering considerations. • Connect to a 10/100 or 10/100/1000 port and run Express Setup. See the Catalyst 3750 Switch Getting Started Guide for instructions. • Connect to the front-panel ports. See the "Connecting to the 10/100 and 10/100/1000 Ports" section on page 2-39 and the "Connecting to an SFP Module" section on page 2-41 to complete the installation. For configuration instructions about using the CLI setup program, go to Appendix D, "Configuring the Switch with the CLI-Based Setup Program." To use the CLI, enter commands at the Switch> prompt through the console port by using a terminal emulation program or through the network by using Telnet. For configuration information, see the switch software configuration guide or the switch command reference. Connecting StackWise Cable to StackWise Ports Follow these steps to connect the StackWise cable to the StackWise ports: Step 1 Step 2 Remove the dust covers from the StackWise cables and StackWise ports, and store them for future use. Insert one end of the StackWise cable into the StackWise port on the back of the switch. (See Figure 2-44.) 2-30 Catalyst 3750 Switch Hardware Installation Guide OL-6336-10

Section	Page
Catalyst 3750 Switch Hardware Installation Guide	1
Preface	7
Audience	7
Purpose	7
Conventions	7
Related Publications	8
Obtaining Documentation, Obtaining Support, and Security Guidelines	9
Product Overview	11
Features	11
Front Panel Description	13
Fast Ethernet Switches	13
Catalyst 3750-24FS and 3750V2-24FS Switch Front Panel	13
Catalyst 3750-24TS and 3750V2-24TS Switch Front Panel	14
Catalyst 3750-48TS and 3750V2-48TS Switch Front Panel	15
Catalyst 3750-24PS and 3750V2-24PS Switch Front Panel	15
Catalyst 3750-48PS and 3750V2-48PS Switch Front Panel	16
Gigabit Ethernet Switches	16
Catalyst 3750G-12S and Catalyst 3750G-12S-SD Switch Front Panel	16
Catalyst 3750-24T, 3750G-24TS, and 3750G-24TS-1U Switch Front Panel	16
Catalyst 3750G-48TS Switch Front Panel	18
Catalyst 3750G-24PS Switch Front Panel	18
Catalyst 3750G-48PS Switch Front Panel	19
Catalyst 3750G-16TD Switch Front Panel	19
Catalyst 3750G Integrated Wireless LAN Controller Switch Front Panel	20
10/100 and 10/100/1000 Ports	20
100BASE-FX Ports	22
SFP Module Slots	22
SFP Modules	23
XENPAK Module Slot (Catalyst 3750G-16TD Switch)	23
LEDs	23
System LED	25
RPS LED	26
Master LED	26
Port LEDs and Modes	27
Rear Panel Description	31
StackWise Ports	34
Power Connectors	35
Internal Power Supply Connector	35
DC Power Connector	35
Cisco RPS Connector	35
Console Port	36
Management Options	36
Network Configurations	37
Switch Installation	39
Preparing for Installation	39
Warnings	40
Installation Guidelines	44
Box Contents	45
Tools and Equipment	45
Verifying Switch Operation	45
Powering On the Switch and Running POST	45
Powering Off the Switch	46
Planning the Stack	46
Planning Considerations	46
Powering Considerations	46
Cabling Considerations	47
Recommended Cabling Configurations	48
Installing the Switch	49
Rack-Mounting	50
Removing Screws from the Switch	50
Attaching Brackets to the Catalyst 3750G-24TS Switch	52
Attaching Brackets to the Catalyst 3750G Integrated Wireless LAN Controller Switches	55
Attaching Brackets to All Other Catalyst 3750 Switches	56
Mounting the Switch in a Rack	62
Attaching the Cable Guide	64
Wall-Mounting	65
Attaching the Brackets to the Switch for Wall-Mounting	66
Attaching the RPS Connector Cover	66
Mounting the Switch on a Wall	67
Table- or Shelf-Mounting	68
Connecting StackWise Cable to StackWise Ports	68
Installing and Removing SFP Modules	71
Installing SFP Modules into SFP Module Slots	71
Removing SFP Modules from SFP Module Slots	72
Installing and Removing XENPAK Modules (Catalyst 3750G-16TD Switch)	73
Installing a XENPAK Module	74
Removing a XENPAK Module	76
Connecting to the 10/100 and 10/100/1000 Ports	77
Connecting to an SFP Module	79
Connecting to a Fiber-Optic SFP Module	79
Connecting to 1000BASE-T SFP Modules	81
Connecting to a XENPAK Module	82
Where to Go Next	83
Troubleshooting	85
Diagnosing Problems	85
Verify Switch POST Results	86
Monitor Switch LEDs	86
Verify Switch Connections	86
Bad or Damaged Cable	86
Ethernet and Fiber Cables	86
Link Status	87
PoE Connections	87
Transceiver Module Port Issues	87
Port and Interface Settings	88
Ping the End Device	88
Spanning Tree Loops	88
Monitor Switch Performance	89
Speed, Duplex, and Autonegotiation	89
Autonegotiation and NIC Cards	89
Cabling Distance	89
Clearing the Switch IP Address and Configuration	90
Replacing a Failed Stack Member	90
Finding the Switch Serial Number	91
Technical Specifications	97
Connector and Cable Specifications	109
Connector Specifications	109
10/100 and 10/100/1000 Ports	110
100BASE-FX Ports	110
SFP Module Ports	111
XENPAK Module Ports (Catalyst 3750G-16TD Switch)	112
Console Port	112
Cable and Adapter Specifications	113
SFP Module Cable Specifications	113
Two Twisted-Pair Cable Pinouts	114
Four Twisted-Pair Cable Pinouts for 10/100 Ports	115
Identifying a Crossover Cable	116
Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports	116
Crossover Cable and Adapter Pinouts	117
Connecting to DC Power	119
Connecting to DC Power	119
Preparing for Installation	119
Grounding the Switch	120
Wiring the DC-Input Power Source	122
Configuring the Switch with the CLI-Based Setup Program	127
Accessing the CLI	128
Accessing the CLI Through Express Setup	128
Accessing the CLI Through the Console Port	128
Taking Out What You Need	129
Stacking the Switches (Optional)	130
Connecting to the Console Port	131
Starting the Terminal Emulation Software	132
Connecting to a Power Source	132
Entering the Initial Configuration Information	133
IP Settings	133

Match case Limit results 1 per page

2-30

Catalyst 3750 Switch Hardware Installation Guide

OL-6336-10

Chapter 2

Switch Installation

Connecting StackWise Cable to StackWise Ports

•

Connect to the front-panel ports. See the

“Connecting to the 10/100 and 10/100/1000 Ports” section

on page 2-39

and the

“Connecting to an SFP Module” section on page 2-41

to complete the

installation.

For configuration instructions about using the CLI setup program, go to

Appendix D, “Configuring the

Switch with the CLI-Based Setup Program.”

To use the CLI, enter commands at the

Switch

> prompt through the console port by using a terminal

program or through the network by using Telnet. For configuration information, see the switch software

configuration guide or the switch command reference.

Table- or Shelf-Mounting

Follow these steps to install the switch on a table or shelf:

Step 1

Locate the adhesive strip with the rubber feet in the mounting-kit envelope. Attach the four rubber feet

to the recessed areas on the bottom of the unit.

Step 2

Place the switch on the table or shelf near an AC power source.

After the switch is mounted on the table, you might need to perform these tasks to complete the

installation, run the setup program, and access the switch:

•

(Optional) Connect the switches in the stacks. See the

“Connecting StackWise Cable to StackWise

Ports” section on page 2-30

•

Power on the switch. See the

“Verifying Switch Operation” section on page 2-7

. If the switches are

stacked, see the

“Planning Considerations” section on page 2-8

for information on powering

considerations.

•

Connect to a 10/100 or 10/100/1000 port and run Express Setup. See the

Catalyst 3750 Switch

Getting Started Guide

for instructions.

•

Connect to the front-panel ports. See the

“Connecting to the 10/100 and 10/100/1000 Ports” section

on page 2-39

and the

“Connecting to an SFP Module” section on page 2-41

to complete the

installation.

For configuration instructions about using the CLI setup program, go to

Appendix D, “Configuring the

Switch with the CLI-Based Setup Program.”

To use the CLI, enter commands at the

Switch

> prompt through the console port by using a terminal

emulation program or through the network by using Telnet. For configuration information, see the switch

software configuration guide or the switch command reference.

Connecting StackWise Cable to StackWise Ports

Follow these steps to connect the StackWise cable to the StackWise ports:

Step 1

Remove the dust covers from the StackWise cables and StackWise ports, and store them for future use.

Step 2

Insert one end of the StackWise cable into the StackWise port on the back of the switch.

(See

Figure 2-44