Compaq ProLiant 1000 Migrating to Microsoft Windows NT Server 4.0 on Compaq Se
Compaq ProLiant 1000 Manual
View all Compaq ProLiant 1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Compaq ProLiant 1000 manual content summary:
- Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 1
6 Compaq Software Support Diskette Installation Overview 8 Migration Scenario 1 10 Migration Scenario 2 14 Migration Scenario 3 17 Migration Scenario 4 20 Upgrading the Compaq Insight Management Agents ... 23 Summary 25 ... Migrating to Microsoft Windows NT Server 4.0 on Compaq Servers The - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 2
and/or service marks of Compaq Computer Corporation. Other product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. ©1997 Compaq Computer Corporation. All rights reserved. Printed in the U.S.A. Microsoft, Windows, Windows NT, Windows NT Server and - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 3
There are many reasons for migrating to Windows NT Server 4.0. Enhancements and new features for Windows NT Server 4.0 provide an ideal platform to support file-and-print, application server, and internet/intranet computing environments. New features and enhancements include: • Better performance - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 4
eliminate this problem by first upgrading the Primary Domain Controller. • If you are upgrading without Compaq SmartStart, you must install the Compaq Support Software, (which updates or installs Compaq device drivers and support software) after installing the Windows NT Server 4.0 operating system - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 5
3.51 support (SSD) • Disable startup options /services • Upgrade Windows NT Server • Upgrade non-Microsoft drivers • Re-install disabled options/services • Install the SSD • Re-install the Compaq Insight Manager Agents • Install the Microsoft Service Pack Backup the Server Compaq highly recommends - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 6
services enabled. Compaq recommends that you disable certain Service and Device Startup settings before beginning a Windows NT Server 4.0 migration. This can reduce the number of warnings similar to the following message from displaying during the installation process: At least one service or driver - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 7
with SNMP Service in step #4. Disabling Compaq ProLiant Storage System and Compaq Systems Management Services Devices You must disable the Compaq ProLiant Storage System setting before you upgrade to Windows NT 4.0 to avoid Service Management errors. 1. Access the Windows NT Server Control Panel - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 8
Service in step #2. 5. Select Close to exit the Devices applet. NOTE: If you plan on maintaining both versions of Windows NT on your server, do not disable the Compaq SCSI Device Monitor. If a warning message displays after the upgrade process is complete, select OK to continue with the installation - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 9
WHITE PAPER (cont.) ... Select the Express button, which installs or upgrades the appropriate drivers depending on your hardware configuration. The following screen is a sample display of the SSD Express selection. Select the update button to continue the SSD installation or upgrade process. 9 - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 10
process and when upgrading from an installation of Windows NT Server 3.51 CD from Compaq SmartStart (SSD 1.18B) on a Compaq ProLiant 5000 directly from the Windows NT 4.0 CD-ROM. TABLE 1 COMPAQ PROLIANT 5000 SERVER MIGRATION SCENARIO 1 CONFIGURATION System Processor(s) Memory Disk Controller Drive - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 11
the latest Compaq Support Software. 7. Press the Enter key to continue. The licensing screen displays. After reading the licensing agreement, press F8 for "I agree" or press ESC for "I do not agree". 8. The next screen asks if you want to: − Press Enter to upgrade, or − Press the letter N to install - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 12
ESC to skip the file; the setup process continues to completion. NOTE: If you have the Compaq Smart SCSI Array Controller installed, a similar message might display. Press ESC to skip the file in each case encountered. 12. When you are prompted, re-start the computer and the set up process continues - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 13
. Reboot the computer or server. If you choose to re-install a pre-existing version, remove the Agents before re-installing. NOTE: Always install the Compaq SSD program and reboot the server before installing the Compaq Insight Manager Agents. 26. You can optionally install Microsoft Service Pack - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 14
using Microsoft Windows NT Server 4.0 CD. TABLE 2 COMPAQ PROLIANT 4000 SERVER MIGRATION SCENARIO 2 CONFIGURATION System Processor(s) Memory Disk Controller Drive Configuration Network Controller Operating System Software Four 166-MHz Pentium Pro 64 MB Compaq SMART-2/P Controller Three 4-GB - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 15
CD-ROM should already be inserted in the drive). Follow all instructions. 5. You are asked either to press Enter to detect a hard disk controller or to press the letter S to skip hard disk detection, press Enter. Follow the instructions as in Scenario 1, steps 7 - 10. At some point during the file - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 16
computer or server. If you choose to re-install a pre-existing version, remove the Agents before re-installing. NOTE: Always install the Compaq SSD program and reboot the server before installing the Compaq Insight Manager Agents. 15. You can optionally install Microsoft Service Pack 2. Your upgrade - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 17
the process when upgrading from an installation of Windows NT Server 3.51 CD to Windows NT 4.0 on a Compaq ProLiant 5000 directly from the Windows NT 4.0 CD-ROM. TABLE 3 COMPAQ PROLIANT 5000 SERVER MIGRATION SCENARIO 3 CONFIGURATION System Processor(s) Memory Disk Controller Drive Configuration - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 18
the system re-starts, the Microsoft install might detect a CPQARRAY, SymbioLogic C810 PCI SCSI Host Adapter, or another type of hard disk controller. You are then asked to enter additional driver information. You should have the latest Compaq Software Support Diskette (SSD 1.20 or higher) available - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 19
Communications, Games, Multimedia and Accessibility Option are selected by default. You may press Enter to continue or change any options. 16. Select the Next button to upgrade the Windows Network Services. 17. A Finish Setup button displays; select this button. 18. The system restarts when the file - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 20
1.20 and Service Pack 5 were installed before the upgrade. 1. Backup your server and registry completely. 2. Obtain and install the latest Compaq Support Software Disk . Secure the latest SmartStart CD to obtain the latest Compaq Support utilities or consult the Compaq Web site (www.compaq.com). If - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 21
the latest Compaq Support Software. 7. Press the Enter key to continue. The licensing screen displays. After reading the licensing agreement, press F8 for "I agree" or ESC for "I do not agree". 8. The next screen asks if you want to − Press Enter to upgrade, or − Press the letter N to install a new - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 22
. 18. Press Enter to continue or choose additional components. 19. Select the Next button to upgrade the Windows Network Services. Setup prompts you to create an Emergency Repair Diskette at this time. Insert a blank, formatted diskette into the drive and select OK. IMPORTANT: Compaq and Microsoft - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 23
. Reboot the computer or server. If you choose to re-install a pre-existing version, remove the Agents before re-installing. NOTE: Always install the Compaq SSD program and reboot the server before installing the Compaq Insight Manager Agents. 27. You can optionally install Microsoft Service Pack - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 24
(cont.) ... 4. 5. 6. 7. 8. Setup prompts that it detects a copy of the Insight Agents on your system. Select Update on this screen to upgrade the Insight Agents on your Windows NT 4.0 platform CD from the CD-ROM drive. Restart the server to implement the latest Compaq Insight Manager Agents. 24 - Compaq ProLiant 1000 | Migrating to Microsoft Windows NT Server 4.0 on Compaq Se - Page 25
there are common basic steps and there are differences because of the specific hardware/software components of your system. Obtain and maintain the latest Compaq software support programs (SSD) and the latest Compaq Insight Manager Agents. Following the steps outlined in this paper should provide
W
HITE
P
APER
1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
467A/0197
[January 1997]
Prepared By
Compaq Windows NT
Integration
Compaq Computer
Corporation
C
ONTENTS
Overview
...........................
3
Windows NT Features
Not Affected by the
Migration
...........................
4
Considerations Before
Migrating
...........................
4
Compaq Migration
Scenarios
..........................
5
Outline of the Migration
Process
.............................
5
Backup the Server
...................
5
Determine Hard Drive
Space Requirements
...............
5
Disable Startup Settings
..........
6
Compaq Software Support
Diskette Installation
Overview
................................
8
Migration Scenario 1
.............
10
Migration Scenario 2
.............
14
Migration Scenario 3
.............
17
Migration Scenario 4
.............
20
Upgrading the Compaq
Insight Management Agents ... 23
Summary
..............................
25
Migrating to Microsoft Windows NT Server
4.0 on Compaq Servers
The information presented in this White Paper provides guidelines and requirements to
migrate Compaq Servers running Microsoft Windows NT Server Version 3.51 to
Microsoft Windows NT Server Version 4.0. This document presumes that you have a
thorough knowledge of Compaq Server products and the Microsoft Windows NT
operating system.
This White Paper includes information on:
•
New features and enhancements for Windows NT Server 4.0
•
Migration considerations
•
Four test migration scenarios
NOTE:
Compaq highly recommends that you read this White Paper from cover-to-cover
BEFORE proceeding with the upgrade process.