Compaq ProLiant CL380 Compaq ProLiant CL380 Software User Guide - Page 19

Insert the Windows NT Server 4.0, Enterprise Edition CD in the drive

Get Compaq ProLiant CL380 PDF manuals and user guides View all Compaq ProLiant CL380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

1-8 Compaq ProLiant CL380 Software User Guide 7. Press the down arrow to select Compaq 64-Bit Dual Channel Wide Ultra2 SCSI Controller (Port1). Underneath this heading is a subheading titled SCSI ID. To change the SCSI ID setting, highlight the SCSI ID option and press Enter. After making a new selection, press Enter to accept the change. IMPORTANT: Make a note of the SCSI ID setting. When server node 2 is configured, it cannot have the same ID as server node 1. For example, if server node 1 is set for SCSI ID 7, then server node 2 must be set to ID 6. 8. Press F10 to exit. 9. Select Step 5: Save and Exit, then press Enter and wait for the Compaq Array Configuration Utility to start. 10. When the Array Configuration Utility starts, select Continue, then click Next. NOTE: The Compaq Array Configuration Utility configures the Integrated Smart Array Controller. Refer to the Compaq Integrated Smart Array Controller User Guide for additional information on using the Compaq Array Configuration Utility. 11. Click Next to select a controller configuration. 12. Select the desired RAID level and click Continue. 13. Click Finish. 14. After the system reboots, SmartStart will finish copying the system partition to the hard drive and will instruct you to replace the SmartStart CD with the operating system CD. SmartStart is no longer involved in the installation process. 15. Insert the Windows NT Server 4.0, Enterprise Edition CD in the drive and start the installation of the operating system by booting directly from the operating system CD. Do not boot the system from diskettes built from the operating system CD. 16. Press the F6 key within five seconds when the Windows NT Setup blue screen appears to begin the array controller driver installation. If dialog displays in the bottom left hand corner of the screen before you press the F6 key, you must restart the installation. NOTE: There will be no text on the screen instructing you to press the F6 key.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
1-8
Compaq ProLiant CL380 Software User Guide
7.
Press the down arrow to select Compaq 64-Bit Dual Channel Wide
Ultra2 SCSI Controller (Port1). Underneath this heading is a subheading
titled SCSI ID. To change the SCSI ID setting, highlight the SCSI ID
option and press
Enter
. After making a new selection, press
Enter
to
accept the change.
IMPORTANT:
Make a note of the SCSI ID setting. When server node 2 is configured, it
cannot have the same ID as server node 1. For example, if server node 1 is set for
SCSI ID 7, then server node 2 must be set to ID 6.
8.
Press
F10
to exit.
9.
Select Step 5: Save and Exit, then press
Enter
and wait for the Compaq
Array Configuration Utility to start.
10.
When the Array Configuration Utility starts, select Continue, then click
Next.
NOTE:
The Compaq Array Configuration Utility configures the Integrated Smart Array
Controller. Refer to the
Compaq Integrated Smart Array Controller User Guide
for
additional information on using the Compaq Array Configuration Utility.
11.
Click Next to select a controller configuration.
12.
Select the desired RAID level and click Continue.
13.
Click Finish.
14.
After the system reboots, SmartStart will finish copying the system
partition to the hard drive and will instruct you to replace the
SmartStart CD with the operating system CD. SmartStart is no longer
involved in the installation process.
15.
Insert the Windows NT Server 4.0, Enterprise Edition CD in the drive
and start the installation of the operating system by booting directly
from the operating system CD. Do not boot the system from diskettes
built from the operating system CD.
16.
Press the
F6
key within five seconds when the Windows NT Setup blue
screen appears to begin the array controller driver installation. If dialog
displays in the bottom left hand corner of the screen before you press the
F6
key, you must restart the installation.
NOTE:
There will be no text on the screen instructing you to press the
F6
key.