Compaq ProLiant CL380 Compaq ProLiant CL380 Software User Guide - Page 69

Channel 0 Target ID, The default mode is NT and it cannot be changed.

Get Compaq ProLiant CL380 PDF manuals and user guides View all Compaq ProLiant CL380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

CR3500 Configuration Utility 4-17 I Channel 0 Target ID-The physical address a bus initiator uses to connect with a bus target. Each bus target is assigned a unique target address. You must select an ID between 0 and 15 for a 16-bit module, or between 0 and 7 for an 8-bit module. Make sure the ID you select does not conflict with other IDs. Target IDs are also referred to as the SCSI ID. NOTE: Compaq recommends using the default values for the Channel 0 Target ID. I Mode-The default mode is NT and it cannot be changed. I Bus width-The default mode is 16 bit and it cannot be changed. I SCSI transfer rate-The default SCSI transfer rate is 40 MB and it cannot be changed. I Tag queuing-If your host adapter supports tag queuing, check the Enabled box. Tag queuing permits each initiator to have multiple commands outstanding and each target to optimize the commands it receives.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
CR3500 Configuration Utility
4-17
■
Channel 0 Target ID
—
The physical address a bus initiator uses to
connect with a bus target. Each bus target is assigned a unique target
address. You must select an ID between 0 and 15 for a 16-bit module, or
between 0 and 7 for an 8-bit module. Make sure the ID you select does
not conflict with other IDs. Target IDs are also referred to as the
SCSI ID.
NOTE:
Compaq recommends using the default values for the Channel 0 Target ID.
■
Mode
—
The default mode is NT and it cannot be changed.
■
Bus width
—
The default mode is 16 bit and it cannot be changed.
■
SCSI transfer rate
—
The default SCSI transfer rate is 40 MB and it
cannot be changed.
■
Tag queuing
—
If your host adapter supports tag queuing, check the
Enabled box. Tag queuing permits each initiator to have multiple
commands outstanding and each target to optimize the commands it
receives.