Compaq ProLiant CL380 Compaq ProLiant CL380 Software User Guide - Page 32

Configuring the Shared Storage, and choose server node 2 from the list.

Get Compaq ProLiant CL380 PDF manuals and user guides View all Compaq ProLiant CL380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

2-4 Compaq ProLiant CL380 Software User Guide IMPORTANT: If the Found New Hardware wizard appears for the CR3500 SCSI Array Device when the system restarts, follow these steps: 1. Click Next. 2. Choose Display a list of known drivers for this device so that I can choose a specific driver. 3. Select Other Devices. 4. Select Unknown under Manufacturers, and select Unsupported Device under Model. 5. Click Finish. 15. Press Print Screen to access the KVM (Keyboard/Video/Mouse) switch and choose server node 2 from the list. NOTE: For detailed instructions on using the KVM switch, refer to the Compaq ProLiant CL380 User Guide. 16. Boot server node 2 with the SmartStart and Support Software CD in the CD-ROM drive. 17. Repeat steps 2 through 14 to configure server node 2. IMPORTANT: Server node 2 may lock up while installing Windows 2000 Advanced Server (step 11 on page 2-3) because the wrong SCSI controller driver is installed automatically. If server node 2 locks up, isolate the node from the shared storage area by pressing the button on the shared storage isolator board that corresponds to server node 2. When server node 2 has been isolated from the shared storage area, installation of the operating system will continue normally. After the Compaq Support Paq for Windows 2000 has been applied (step 14 on page 2-3), reboot server node 2 and press the shared storage isolator board button again to allow server node 2 to gain access to the shared storage area. 18. Continue with the system configuration by performing the steps in the following section, "Configuring the Shared Storage." Configuring the Shared Storage 1. Press Print Screen to access the KVM (Keyboard/Video/Mouse) switch and choose server node 1 from the list. NOTE: For detailed instructions on using the KVM switch, refer to the Compaq ProLiant CL380 User Guide.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
2-4
Compaq ProLiant CL380 Software User Guide
IMPORTANT:
If the Found New Hardware wizard appears for the CR3500 SCSI Array
Device when the system restarts, follow these steps:
1.
Click Next.
2.
Choose Display a list of known drivers for this device so that I can choose a specific
driver.
3.
Select Other Devices.
4.
Select Unknown under Manufacturers, and select Unsupported Device under Model.
5.
Click Finish.
15.
Press
Print Screen
to access the KVM (Keyboard/Video/Mouse) switch
and choose server node 2 from the list.
NOTE:
For detailed instructions on using the KVM switch, refer to the
Compaq ProLiant CL380 User Guide
.
16.
Boot server node 2 with the SmartStart and Support Software CD in the
CD-ROM drive.
17.
Repeat steps 2 through 14 to configure server node 2.
IMPORTANT:
Server node 2 may lock up while installing Windows 2000 Advanced Server
(step 11 on page 2-3) because the wrong SCSI controller driver is installed automatically.
If server node 2 locks up, isolate the node from the shared storage area by pressing the
button on the shared storage isolator board that corresponds to server node 2. When
server node 2 has been isolated from the shared storage area, installation of the operating
system will continue normally.
After the Compaq Support Paq for Windows 2000 has been applied (step 14 on page 2-3),
reboot server node 2 and press the shared storage isolator board button again to allow
server node 2 to gain access to the shared storage area.
18.
Continue with the system configuration by performing the steps in the
following section, “Configuring the Shared Storage.”
Configuring the Shared Storage
1.
Press
Print Screen
to access the KVM (Keyboard/Video/Mouse) switch
and choose server node 1 from the list.
NOTE:
For detailed instructions on using the KVM switch, refer to the
Compaq ProLiant CL380 User Guide
.