D-Link DCS-3420 Product Manual - Page 64

Reset and Restore - blinking green

Get D-Link DCS-3420 - Wireless Day And Night Internet Camera Network PDF manuals and user guides
UPC - 790069289811
View all D-Link DCS-3420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Section 3 - Configuration Reset and Restore There is a button hidden in the pinhole beside the power socket. It is used to reset the system or restore the factory default settings. Sometimes resetting the DCS-3420 will return the system back to a normal state. If the system still has problems after reset, restore the factory settings and install again: RESET: 1. Lightly insert a paper clip (or a similar sized tool) into the reset hole on the back of the camera, press lightly and then release the button. 2. The LED on the back of the camera will begin blinking red and green fast. 3. When the LED stops the blinking fast and starts blinking once every second, the reset is completed. RESTORE:1. Insert the paper clip, or another similar tool, and press and continuously hold down the button recessed inside the reset hole. 2. Wait for the LED on the back of the camera to blink red and green and hold the button through two cycles of blinking (about 5-7 seconds.) 3. Withdraw the tool after the second cycle of the LED blinking and a factory restore has been completed. Reset Button Note: Restoring the factory defaults will result in the loss of any previous settings and will require running the IP Installer to find the camera's IP address. D-Link DCS-3420 User Manual 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
³4
D-Link DCS-34±0 User Manual
Section 3 - Configuration
There is a button hidden in the pinhole beside the power socket. It is used to
reset
the system or
restore
the factory
default settings. Sometimes resetting the DCS-3420 will return the system back to a normal state. If the system still
has problems after reset, restore the factory settings and install again:
RESET
:
1. Lightly insert a paper clip (or a similar sized tool) into the reset hole on the back of the camera, press
lightly and then release the button.
2. The LED on the back of the camera will begin blinking red and green fast.
3. When the LED stops the blinking fast and starts blinking once every second, the reset is completed.
RESTORE
: 1. Insert the paper clip, or another similar tool, and press
and continuously hold down the button
recessed inside the reset hole.
2. Wait for the LED on the back of the camera to blink red and green and hold the button through two
cycles of blinking (about 5-7 seconds.)
3. Withdraw the tool after the second cycle of the LED blinking and a factory restore has been
completed.
Reset and Restore
Reset Button
Note:
Restoring the factory defaults will result in the loss of any previous settings and will require running the IP Installer
to find the camera’s IP address.