Dell E6500 Service Manual - Page 20

Replacing the Display Assembly, Removing the Display Bezel - wireless not working

Get Dell E6500 - Latitude - Core 2 Duo 2.53 GHz PDF manuals and user guides
UPC - 884116029793
View all Dell E6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

8. Turn the computer top-side up. 9. Open the display to 90-degrees and lift the display assembly off the base assembly. 1 display assembly 2 base assembly Replacing the Display Assembly Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance. CAUTION: After unrouting cables, position the cables to the rear and away from the base assembly before installing the display assembly. 1. Align the display hinges with the holes in the base of the computer and lower the display into place. 2. Replace the two each M2.5 x 5-mm screws on the hinges. 3. Close the display and turn the computer over. 4. Route the display cable and wireless (WLAN, WWAN, and WPAN) cables, and fit the cables under each tab in the cable routing channels, including the tabs on the rear of the assembly. 5. Connect the WWAN antenna cables to the WWAN card and place any unused antenna cables in the base assembly cable holders next to the card slot. 6. Connect the WPAN antenna cable to the WPAN card and place any unused antenna cables in the base assembly cable holders next to the card slot. 7. Connect the WLAN antenna cables to the WPAN card, and place any unused antenna cables in the base assembly cable holders next to the card slot. 8. Connect the display cable to the display cable connector on the system board. 9. Replace the hinge covers (see Replacing the Hinge Covers). 10. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly). 11. Replace the battery (see Replacing the Battery). Removing the Display Bezel Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance. 1. Follow the instructions in Before Working on Your Computer. 2. Remove the display assembly (see Removing the Display Assembly).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
8.
Turn the computer top-side up.
9.
Open the display to 90-degrees and lift the display assembly off the base assembly.
Replacing the Display Assembly
Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the
Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance.
1.
Align the display hinges with the holes in the base of the computer and lower the display into place.
2.
Replace the two each M2.5 x 5-mm screws on the hinges.
3.
Close the display and turn the computer over.
4.
Route the display cable and wireless (WLAN, WWAN, and WPAN) cables, and fit the cables under each tab in the cable routing channels, including the
tabs on the rear of the assembly.
5.
Connect the WWAN antenna cables to the WWAN card and place any unused antenna cables in the base assembly cable holders next to the card slot.
6.
Connect the WPAN antenna cable to the WPAN card and place any unused antenna cables in the base assembly cable holders next to the card slot.
7.
Connect the WLAN antenna cables to the WPAN card, and place any unused antenna cables in the base assembly cable holders next to the card slot.
8.
Connect the display cable to the display cable connector on the system board.
9.
Replace the hinge covers (see
Replacing the Hinge Covers
).
10.
Replace the bottom of the base assembly (see
Replacing the Bottom of the Base Assembly
).
11.
Replace the battery (see
Replacing the Battery
).
Removing the Display Bezel
Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the
Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance.
1.
Follow the instructions in
Before Working on Your Computer
.
2.
Remove the display assembly (see
Removing the Display Assembly
).
1
display assembly
2
base assembly
CAUTION:
After unrouting cables, position the cables to the rear and away from the base assembly before installing the display assembly.