Dell PowerEdge T320 Owner's Manual - Page 106

Removing The Control-Panel Assembly

Get Dell PowerEdge T320 PDF manuals and user guides View all Dell PowerEdge T320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

The control-panel assembly with diagnostic indicators is supported on systems with cabled hard drives and systems with an x8 backplane. The control-panel assembly with LCD module is supported on systems with hot-swappable hard drives only. Removing The Control-Panel Assembly CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. If installed, remove the front bezel. 2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and peripherals. 3. Open the system. 4. Remove the screw on the side of the chassis that secures the control-panel assembly to the chassis. 5. Slide the control-panel assembly out of the chassis. CAUTION: Do not use excessive force when removing the control panel cable as it can damage the connectors. 6. Remove the control panel cable and if applicable, the VGA module cable from the control-panel assembly. NOTE: Ensure that the control panel cable and if applicable, the VGA module cable, does not slip back into the chassis. Figure 56. Removing and Installing the Control-Panel assembly With an LCD Module in a Tower-Mode System 1. LCD module ZIF connector 2. control-panel assembly connector 3. control-panel assembly cable connector 4. screw 106

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
The control-panel assembly with diagnostic indicators is supported on systems with cabled hard drives and systems
with an x8 backplane. The control-panel assembly with LCD module is supported on systems with hot-swappable hard
drives only.
Removing The Control-Panel Assembly
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
1.
If installed, remove the front bezel.
2.
Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and
peripherals.
3.
Open the system.
4.
Remove the screw on the side of the chassis that secures the control-panel assembly to the chassis.
5.
Slide the control-panel assembly out of the chassis.
CAUTION: Do not use excessive force when removing the control panel cable as it can damage the connectors.
6.
Remove the control panel cable and if applicable, the VGA module cable from the control-panel assembly.
NOTE:
Ensure that the control panel cable and if applicable, the VGA module cable, does not slip back into the
chassis.
Figure 56. Removing and Installing the Control-Panel assembly With an LCD Module in a Tower-Mode System
1. LCD module ZIF connector
2. control-panel assembly connector
3. control-panel assembly cable connector
4. screw
106