Dell PowerEdge T320 Owner's Manual - Page 11

To reset integrated Dell Remote Access Controller, On Advanced Configuration and Power - drivers

Get Dell PowerEdge T320 PDF manuals and user guides View all Dell PowerEdge T320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Item Indicator, Button, or Icon Description Connector 4 Power-on indicator, power button The power-on indicator lights when the system power is on. The power button controls the power supply output to the system. NOTE: On Advanced Configuration and Power Interface (ACPI)-compliant operating systems, turning off the system using the power button causes the system to perform a graceful shutdown before power to the system is turned off. 5 NMI button 6 System identification button 7 LCD menu buttons 8 Information tag 9 LCD panel Used to troubleshoot software and device driver errors when running certain operating systems. This button can be pressed using the end of a paper clip. Use this button only if directed to do so by qualified support personnel or by the operating system documentation. The identification buttons on the front and back panels of the system can be used to locate a particular system within a rack. When one of these buttons is pressed, the LCD panel on the front and the system status indicator on the back flash until one of the buttons is pressed again. Press to toggle the system ID on and off. If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter BIOS progress mode. To reset integrated Dell Remote Access Controller (iDRAC) (if not disabled in F2 iDRAC setup), press and hold for more than 15 seconds. Allow you to navigate the control panel LCD menu. A slide-out label panel which allows you to record system information such as Service Tag, NIC, MAC address, and so on. Displays system ID, status information, and system error messages. The LCD lights blue during normal system operation. The LCD lights amber when the system needs attention, and displays an error code followed by descriptive text. NOTE: If the system is connected to a power source and an error is detected, the LCD lights amber regardless of whether the system is turned on or off. 10 USB connectors (2) 11 Hard drives Allow you to connect USB devices to the system. The ports are USB 2.0-compliant. Your system supports one of the following configurations: • Up to eight 3.5 inch hot-swappable hard drives • Up to eight 2.5 inch hot-swappable hard drives installed in the 3.5 inch hard-drive carriers 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
Item
Indicator, Button, or
Connector
Icon
Description
4
Power-on indicator, power
button
The power-on indicator lights when the system power is
on. The power button controls the power supply output to
the system.
NOTE:
On Advanced Configuration and Power
Interface (ACPI)-compliant operating systems, turning
off the system using the power button causes the
system to perform a graceful shutdown before power
to the system is turned off.
5
NMI button
Used to troubleshoot software and device driver errors
when running certain operating systems. This button can
be pressed using the end of a paper clip.
Use this button only if directed to do so by qualified
support personnel or by the operating system
documentation.
6
System identification button
The identification buttons on the front and back panels of
the system can be used to locate a particular system
within a rack. When one of these buttons is pressed, the
LCD panel on the front and the system status indicator on
the back flash until one of the buttons is pressed again.
Press to toggle the system ID on and off.
If the system stops responding during POST, press and
hold the system ID button for more than five seconds to
enter BIOS progress mode.
To reset integrated Dell Remote Access Controller
(iDRAC) (if not disabled in F2 iDRAC setup), press and hold
for more than 15 seconds.
7
LCD menu buttons
Allow you to navigate the control panel LCD menu.
8
Information tag
A slide-out label panel which allows you to record system
information such as Service Tag, NIC, MAC address, and
so on.
9
LCD panel
Displays system ID, status information, and system error
messages. The LCD lights blue during normal system
operation. The LCD lights amber when the system needs
attention, and displays an error code followed by
descriptive text.
NOTE:
If the system is connected to a power source
and an error is detected, the LCD lights amber
regardless of whether the system is turned on or off.
10
USB connectors (2)
Allow you to connect USB devices to the system. The
ports are USB 2.0-compliant.
11
Hard drives
Your system supports one of the following configurations:
•
Up to eight 3.5 inch hot-swappable hard drives
•
Up to eight 2.5 inch hot-swappable hard drives
installed in the 3.5 inch hard-drive carriers
11