Epson MovieMate 72 User's Guide - Page 54

warning light is flashing orange or red., button is flashing orange and green and - air filter

Get Epson MovieMate 72 PDF manuals and user guides View all Epson MovieMate 72 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

The Image Off light is orange and the light is green. Press on the remote control or control panel to turn the lamp back on. The warning light is flashing orange. High-speed cooling is in process. If Epson MovieMate gets too hot again, projection stops automatically. Make sure Epson MovieMate is at least 8 inches (20 cm) away from the wall. Clean or replace the air filters if necessary (see page 46). If you are using Epson MovieMate at an altitude above 4900 feet (1500 meters), turn on High Altitude Mode (see page 44). The warning light is flashing orange or red. The lamp needs to be replaced. See page 48. The button is flashing orange and green and the warning light is red. Epson MovieMate is too hot and has turned off the lamp. Make sure Epson MovieMate is at least 8 inches (20 cm) away from the wall. Clean or replace the air filters if necessary (see page 46). If you are using Epson MovieMate at an altitude above 4900 feet (1500 meters), turn on High Altitude Mode (see page 44). Let Epson MovieMate cool for five minute. When the Image Off light turns orange, press to turn the lamp on. If the status doesn't change, wait a few minutes, then unplug Epson MovieMate and contact Epson. See page 60. The button is flashing orange and green and the warning light is flashing red. The lamp may be incorrectly installed, the lamp cover may be loose, or the lamp may be broken. Turn off the power and check the lamp. See page 48. If the lamp is broken, or the lights continue to flash after you turn the power back on, unplug Epson MovieMate and contact Epson. See page 60. The button is flashing orange and green and the warning light is flashing red. Epson MovieMate has a problem with its fan or temperature sensor. Wait a few minutes, then unplug Epson MovieMate and contact Epson. See page 60. 54 Problem Solving

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
54
Problem Solving
The
Image Off
light is orange and the
light is green.
Press
on the remote control or control panel to turn the lamp back on.
The
warning light is flashing orange.
High-speed cooling is in process. If Epson MovieMate gets too hot again, projection stops
automatically. Make sure Epson MovieMate is at least 8 inches (20 cm) away from the wall.
Clean or replace the air filters if necessary (see page 46). If you are using Epson MovieMate at
an altitude above 4900 feet (1500 meters), turn on High Altitude Mode (see page 44).
The
warning light is flashing orange or red.
The lamp needs to be replaced. See page 48.
The
button is flashing orange and green and the
warning light is red.
Epson MovieMate is too hot and has turned off the lamp. Make sure Epson MovieMate is at
least 8 inches (20 cm) away from the wall.
Clean or replace the air filters if necessary (see page 46). If you are using Epson MovieMate at
an altitude above 4900 feet (1500 meters), turn on High Altitude Mode (see page 44).
Let Epson MovieMate cool for five minute. When the
Image Off
light turns orange, press
to turn the lamp on. If the status doesn’t change, wait a few minutes, then unplug Epson
MovieMate and contact Epson. See page 60.
The
button is flashing orange and green and the
warning light is flashing
red.
The lamp may be incorrectly installed, the lamp cover may be loose, or the lamp may be
broken. Turn off the power and check the lamp. See page 48. If the lamp is broken, or the
lights continue to flash after you turn the power back on, unplug Epson MovieMate and
contact Epson. See page 60.
The
button is flashing orange and green and the
warning light is flashing
red.
Epson MovieMate has a problem with its fan or temperature sensor. Wait a few minutes, then
unplug Epson MovieMate and contact Epson. See page 60.