Epson WorkForce 600 Quick Guide - Page 41

into place., Insert the new ink cartridge into the holder and push it down until it clicks - cartridges

Get Epson WorkForce 600 - All-in-One Printer PDF manuals and user guides View all Epson WorkForce 600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

3. Squeeze the tab on the cartridge and lift it straight up. Dispose of it carefully. Do not take the used cartridge apart or try to refill it. Warning: If ink gets on your hands, wash them thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water. Keep ink cartridges out of the reach of children. 4. Shake the cartridge several times, then remove it from the package. Do not to touch the green chip on the side. 5. Remove the yellow tape from the bottom of the ink cartridge. Caution: Do not remove any other labels or seals, or ink will leak. 6. Insert the new ink cartridge into the holder and push it down until it clicks into place. 7. Once you replace all the cartridges that need replacing, close the cartridge cover and push it down until it clicks into place. 8. Close the scanner. 9. Press OK to begin charging the ink. This takes about 2 minutes. When you see a completion message on the display screen, ink charging is finished. Caution: To conserve ink, never turn off the WorkForce 600 Series while ink is charging. If you see an ink replacement message on the display screen, press OK and press down all the cartridges securely. If you remove a low or expended ink cartridge, you cannot reinstall and use the cartridge. Replacing Ink Cartridges 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Replacing Ink Cartridges
41
3.
Squeeze the tab on the cartridge and lift it straight
up. Dispose of it carefully. Do not take the used
cartridge apart or try to refill it.
Warning:
If ink gets on your hands, wash them thoroughly with
soap and water. If ink gets into your eyes, flush them
immediately with water. Keep ink cartridges out of the
reach of children.
4.
Shake the cartridge several times,
then remove it from the package.
Do not to touch the green chip on
the side.
5.
Remove the yellow tape from the
bottom of the ink cartridge.
Caution:
Do not remove any other labels or seals, or ink will leak.
6.
Insert the new ink cartridge into the holder and push it down until it clicks
into place.
7.
Once you replace all the cartridges that need replacing, close the cartridge
cover and push it down until it clicks into place.
8.
Close the scanner.
9.
Press
OK
to begin charging the ink. This takes about 2 minutes. When you
see a completion message on the display screen, ink charging is finished.
Caution:
To conserve ink, never turn off the WorkForce 600 Series while ink is charging. If you
see an ink replacement message on the display screen, press
OK
and press down all
the cartridges securely.
If you remove a low or expended ink cartridge, you cannot reinstall and use the
cartridge.