Fluke Ti55FT-20 User Manual - Page 65

Adjusting Display Screen Brightness, Temperature Scale, Camera Settings

Get Fluke Ti55FT-20 PDF manuals and user guides View all Fluke Ti55FT-20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

6 Camera Setup Setting Temperature Units 5. Position the pointer over the Temperature Scale box and tap E. A check mark indicates function is enabled. 6. Tap to accept setting change and return to scan target mode. Setting Temperature Units To set or change temperature units to Celsius, Fahrenheit, or Kelvin: 1. Use the mouse controller to position the pointer over the temperature unit mark (ºF, ºK, ºC) on the task bar and tap E. 2. Repeat until the desired unit is selected. Setting Temperature Calibration Range You can change the temperature calibration range as needed: the narrower the range the better the image quality, which enables you to see smaller temperature variances. The wider the range the lower the image quality; however, you are able to see a greater range of temperature variances. To set the temperature calibration range: Note Calibration range cannot be changed on a paused or saved image. Be sure to select the correct calibration range prior to pausing or saving an image. See Appendix D to determine the calibrated temperature ranges available for your camera model. 1. Tap F. 2. Use the mouse controller to position the pointer over Camera Settings on the popup menu and tap E. 3. Position the pointer over the Lens tab and tap E. 4. Position the pointer over the calibration range radio button you want and tap E. 5. Tap to accept setting change and return to scan target mode. Changing Lens Selection To change the lens selection to match the installed lens: 6-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Camera Setup
Setting Temperature Units
6
6-3
5.
Position the pointer over the
Temperature Scale
box and tap
E
. A
check mark indicates function is enabled.
6.
Tap
to accept setting change and return to scan target mode.
Setting Temperature Units
To set or change temperature units to Celsius, Fahrenheit, or Kelvin:
1.
Use the mouse controller to position the pointer over the temperature unit
mark (ºF, ºK, ºC) on the task bar and tap
E
.
2.
Repeat until the desired unit is selected.
Setting Temperature Calibration Range
You can change the temperature calibration range as needed: the narrower the
range the better the image quality, which enables you to see smaller
temperature variances. The wider the range the lower the image quality;
however, you are able to see a greater range of temperature variances.
To set the temperature calibration range:
Note
Calibration range cannot be changed on a paused or saved image. Be
sure to select the correct calibration range prior to pausing or saving
an image. See Appendix D to determine the calibrated temperature
ranges available for your camera model.
1.
Tap
F
.
2.
Use the mouse controller to position the pointer over
Camera Settings
on
the popup menu and tap
E
.
3.
Position the pointer over the
Lens
tab and tap
E
.
4.
Position the pointer over the calibration range radio button you want and
tap
E
.
5.
Tap
to accept setting change and return to scan target mode.
Changing Lens Selection
To change the lens selection to match the installed lens: