HP 6400/8400 HP StorageWorks 6400/8400 Enterprise Virtual Array User Guide - Page 31

Setting up a controller pair using the OCP, Entering the WWN

Get HP 6400/8400 PDF manuals and user guides View all HP 6400/8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

• Operating system type • Available LUN numbers Setting up a controller pair using the OCP NOTE: This procedure should be performed by an HP authorized service representative. Two pieces of data must be entered during initial setup using the controller OCP: • World Wide Name (WWN) - Required to complete setup. This procedure should be performed by an HP authorized service representative. • Storage system password - Optional. A password provides security allowing only specific instances of HP P6000 Command View to access the storage system. The OCP on either controller can be used to input the WWN and password data. For more information about the OCP, see "Operator Control Panel" (page 14). Table 9 (page 31) lists the push-button functions when entering the WWN, WWN checksum, and password data. Table 9 Push button functions Button Function Selects a character by scrolling up through the character list one character at a time. Moves forward one character. If you accept an incorrect character, you can move through all 16 characters, one character at a time, until you display the incorrect character. You can then change the character. Selects a character by scrolling down through the character list one character at a time. Moves backward one character. ESC ENTER Returns to the default display. Accepts all the characters entered. Entering the WWN Fibre Channel protocol requires that each controller pair have a unique WWN. This 16-character alphanumeric name identifies the controller pair on the storage system. Two WWN labels attached to the rack identify the storage system WWN and checksum. See Figure 24 (page 32). Procedures for getting started 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
•
Operating system type
•
Available LUN numbers
Setting up a controller pair using the OCP
NOTE:
This procedure should be performed by an HP authorized service representative.
Two pieces of data must be entered during initial setup using the controller OCP:
•
World Wide Name (WWN) — Required to complete setup. This procedure should be
performed by an HP authorized service representative.
•
Storage system password — Optional. A password provides security allowing only specific
instances of HP P6000 Command View to access the storage system.
The OCP on either controller can be used to input the WWN and password data. For more
information about the OCP, see
“Operator Control Panel” (page 14)
.
Table 9 (page 31)
lists the push-button functions when entering the WWN, WWN checksum, and
password data.
Table 9 Push button functions
Function
Button
Selects a character by scrolling up through the character list one character at a time.
Moves forward one character. If you accept an incorrect character, you can move through all 16
characters, one character at a time, until you display the incorrect character. You can then change
the character.
Selects a character by scrolling down through the character list one character at a time.
Moves backward one character.
Returns to the default display.
ESC
Accepts all the characters entered.
ENTER
Entering the WWN
Fibre Channel protocol requires that each controller pair have a unique WWN. This 16-character
alphanumeric name identifies the controller pair on the storage system. Two WWN labels attached
to the rack identify the storage system WWN and checksum. See
Figure 24 (page 32)
.
Procedures for getting started
31