HP BL10e HP ProLiant BL e-Class System Maintenance and Service Guide - Page 30

Removing the Server Blade Enclosure from the Rack

Get HP BL10e - ProLiant - G2 PDF manuals and user guides
UPC - 808736933599
View all HP BL10e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Removal and Replacement Procedures Removing the Server Blade Enclosure from the Rack WARNING: Rack rails do not have safety latches. Be sure that at least two persons are available to prevent the enclosure from falling and causing bodily harm when removing it from the rack. To remove the server blade enclosure from the rack: 1. Power down each server blade. See the "Powering Down a Server Blade" section in this chapter. 2. Power down the enclosure. See the "Powering Down the Enclosure" section in this chapter. 3. Disconnect all cables and power cords from the AC power source. 4. Disconnect all cables and power cords from the enclosure rear panel. 5. Remove all server blades and server blade blanks. See the "Removing a Server Blade" and the "Removing a Server Blade Blank" sections in this chapter. CAUTION: Integrated Administrator security settings are assigned to server blade bays, not to server blades. If server blades change locations within the enclosure, Integrated Administrator settings must also be adjusted to ensure accurate security. Refer to the HP ProLiant BL e-Class Integrated Administrator User Guide for more information on security settings. 6. Remove both hot-plug power supplies. See the "Hot-Plug Power Supplies" section in this chapter. 7. Remove the interconnect tray. See the "Removing the Interconnect Tray" section in this chapter. HP ProLiant BL e-Class System Maintenance and Service Guide HP CONFIDENTIAL Codename: MacDuff Part Number: 249066-005 Last Saved On: 7/11/03 7:27 AM 2-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Removal and Replacement Procedures
Removing the Server Blade Enclosure from the Rack
WARNING:
Rack rails do not have safety latches. Be sure that at least two persons are
available to prevent the enclosure from falling and causing bodily harm when removing
it from the rack.
To remove the server blade enclosure from the rack:
1.
Power down each server blade. See the “Powering Down a Server Blade” section in this
chapter.
2.
Power down the enclosure. See the “Powering Down the Enclosure” section in this
chapter.
3.
Disconnect all cables and power cords from the AC power source.
4.
Disconnect all cables and power cords from the enclosure rear panel.
5.
Remove all server blades and server blade blanks. See the “Removing a Server Blade”
and the “Removing a Server Blade Blank” sections in this chapter.
CAUTION:
Integrated Administrator security settings are assigned to server blade bays, not
to server blades. If server blades change locations within the enclosure, Integrated
Administrator settings must also be adjusted to ensure accurate security. Refer to the
HP
ProLiant BL e-Class Integrated Administrator User Guide
for more information on security
settings.
6.
Remove both hot-plug power supplies. See the “Hot-Plug Power Supplies” section in this
chapter.
7.
Remove the interconnect tray. See the “Removing the Interconnect Tray” section in this
chapter.
HP ProLiant BL e-Class System Maintenance and Service Guide
2-15
HP CONFIDENTIAL
Codename: MacDuff Part Number: 249066-005 Last Saved On: 7/11/03 7:27 AM