HP BL10e HP ProLiant BL e-Class System Maintenance and Service Guide - Page 31

Opening the Access Door, Removing the enclosure from the rack

Get HP BL10e - ProLiant - G2 PDF manuals and user guides
UPC - 808736933599
View all HP BL10e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Removal and Replacement Procedures 8. Loosen the thumbscrews on the front of the enclosure (1). 9. Remove the enclosure from the rack (2). IMPORTANT: Pull the enclosure out using the handles. Pulling the enclosure by the thumbscrews damages the thumbscrews. Figure 2-11: Removing the enclosure from the rack Reverse steps 1 through 9 to install the enclosure into the rack. Opening the Access Door To open the access door: 1. Power down each server blade. See the "Powering Down a Server Blade" section in this chapter. 2. Power down the enclosure. See the "Powering Down the Enclosure" section in this chapter. 3. Disconnect all cables and power cords from the AC power source. 4. Disconnect all cables and power cords from the enclosure rear panel. 5. Remove all server blades and server blade blanks. See the "Removing a Server Blade" and the "Removing a Server Blade Blank" sections in this chapter. CAUTION: Integrated Administrator security settings are assigned to server blade bays, not to server blades. If server blades change locations within the enclosure, Integrated Administrator settings must also be adjusted to ensure accurate security. Refer to the HP ProLiant BL e-Class Integrated Administrator User Guide for more information on security settings. 6. Remove the enclosure from the rack. See the "Removing the Enclosure from the Rack" section in this chapter. 2-16 HP ProLiant BL e-Class System Maintenance and Service Guide HP CONFIDENTIAL Codename: MacDuff Part Number: 249066-005 Last Saved On: 7/11/03 7:27 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Removal and Replacement Procedures
8.
Loosen the thumbscrews on the front of the enclosure (1).
9.
Remove the enclosure from the rack (2).
IMPORTANT:
Pull the enclosure out using the handles. Pulling the enclosure by the thumbscrews
damages the thumbscrews.
Figure 2-11: Removing the enclosure from the rack
Reverse steps 1 through 9 to install the enclosure into the rack.
Opening the Access Door
To open the access door:
1.
Power down each server blade. See the “Powering Down a Server Blade” section in this
chapter.
2.
Power down the enclosure. See the “Powering Down the Enclosure” section in this
chapter.
3.
Disconnect all cables and power cords from the AC power source.
4.
Disconnect all cables and power cords from the enclosure rear panel.
5.
Remove all server blades and server blade blanks. See the “Removing a Server Blade”
and the “Removing a Server Blade Blank” sections in this chapter.
CAUTION:
Integrated Administrator security settings are assigned to server blade bays, not
to server blades. If server blades change locations within the enclosure, Integrated
Administrator settings must also be adjusted to ensure accurate security. Refer to the
HP
ProLiant BL e-Class Integrated Administrator User Guide
for more information on security
settings.
6.
Remove the enclosure from the rack. See the “Removing the Enclosure from the Rack”
section in this chapter.
2-16
HP ProLiant BL e-Class System Maintenance and Service Guide
HP CONFIDENTIAL
Codename: MacDuff Part Number: 249066-005 Last Saved On: 7/11/03 7:27 AM