HP DL360 ProLiant DL360 Generation 3 Server Maintenance and Service Guide - Page 16

Activating the Front Unit Identification LED and, powering down the server

Get HP DL360 - ProLiant - G3 PDF manuals and user guides
UPC - 613326948835
View all HP DL360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Removal and Replacement Procedures CAUTION: The system power in the server does not completely shut off from the front Power On/Standby switch. Moving the switch from On to Standby leaves some portion of the power supply and some internal circuitry active. Disconnect all power cords from the server to remove all power from the system. CAUTION: Electrostatic discharge may damage electronic components. Be sure you are properly grounded before beginning any installation procedure. For more information, refer to "Electrostatic Discharge Information" earlier in this chapter. To power down the server: 1. Shut down the operating system as directed in the operating system instructions. CAUTION: Whenever installing hardware or performing maintenance procedures requiring access to internal components, it is recommended that all server data be backed up to avoid loss. 2. Press the Unit Identification switch on the server front panel (1). An LED illuminates blue on the server front and rear panels. 3. Press the server Power On/Standby switch (2) to power down the server. The Power On/Off LED (2) changes from green to amber, indicating standby mode. Figure 2-1: Activating the Front Unit Identification LED and powering down the server HP ProLiant DL360 Generation 3 Server Maintenance and Service Guide 2-5 HP CONFIDENTIAL Codename: Introv-ERTL Part Number: 293948-005 Last Saved On: 2/27/04 2:49 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Removal and Replacement Procedures
CAUTION:
The system power in the server does not completely shut off from the front
Power On/Standby switch. Moving the switch from On to Standby leaves some portion of the
power supply and some internal circuitry active. Disconnect all power cords from the server to
remove all power from the system.
CAUTION:
Electrostatic discharge may damage electronic components. Be sure you are
properly grounded before beginning any installation procedure. For more information, refer to
“Electrostatic Discharge Information” earlier in this chapter.
To power down the server:
1.
Shut down the operating system as directed in the operating system instructions.
CAUTION:
Whenever installing hardware or performing maintenance
procedures requiring access to internal components, it is recommended that all
server data be backed up to avoid loss.
2.
Press the Unit Identification switch on the server front panel (1). An LED illuminates
blue on the server front and rear panels.
3.
Press the server Power On/Standby switch (2) to power down the server. The Power
On/Off LED (2) changes from green to amber, indicating standby mode.
Figure 2-1:
Activating the Front Unit Identification LED and
powering down the server
HP ProLiant DL360 Generation 3 Server Maintenance and Service Guide
2-5
HP CONFIDENTIAL
Codename: Introv-ERTL Part Number: 293948-005 Last Saved On: 2/27/04 2:49 PM