HP DL360 ProLiant DL360 Generation 3 Server Maintenance and Service Guide - Page 33

PCI Riser Board Assembly, Replacing an Expansion Board

Get HP DL360 - ProLiant - G3 PDF manuals and user guides
UPC - 613326948835
View all HP DL360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Removal and Replacement Procedures 4. Connect the power cord. PCI Riser Board Assembly The procedures in this section assume that the server is configured with two PCI riser board assemblies. To remove the PCI riser board assembly: 1. Power down the server. Refer to "Powering Down the Server" earlier in this chapter. 2. Remove the server from the rack. Refer to "Removing the Server from the Rack" earlier in this chapter. 3. Remove the access panel. Refer to "Server Access Panel" earlier in this chapter. 4. Loosen the PCI riser board thumbscrew (1). 5. Lift the front of the assembly slightly (2), and then pull it out from the server chassis PCI expansion board slot (3). Figure 2-23: Removing the PCI riser board assembly Reverse steps 1 through 5 to replace the PCI riser board assembly. Replacing an Expansion Board To replace an expansion board: 1. Power down the server. Refer to "Powering Down the Server" earlier in this chapter. 2. Remove the server from the rack. Refer to "Removing the Server from the Rack" earlier in this chapter. 3. Remove the access panel. Refer to "Server Access Panel" earlier in this chapter. 2-22 HP ProLiant DL360 Generation 3 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Introv-ERTL Part Number: 293948-005 Last Saved On: 2/27/04 2:49 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Removal and Replacement Procedures
4.
Connect the power cord.
PCI Riser Board Assembly
The procedures in this section assume that the server is configured with two PCI riser board
assemblies.
To remove the PCI riser board assembly:
1.
Power down the server. Refer to “Powering Down the Server” earlier in this chapter.
2.
Remove the server from the rack. Refer to “Removing the Server from the Rack” earlier
in this chapter.
3.
Remove the access panel. Refer to “Server Access Panel” earlier in this chapter.
4.
Loosen the PCI riser board thumbscrew (1).
5.
Lift the front of the assembly slightly (2), and then pull it out from the server chassis PCI
expansion board slot (3).
Figure 2-23: Removing the PCI riser board assembly
Reverse steps 1 through 5 to replace the PCI riser board assembly.
Replacing an Expansion Board
To replace an expansion board:
1.
Power down the server. Refer to “Powering Down the Server” earlier in this chapter.
2.
Remove the server from the rack. Refer to “Removing the Server from the Rack” earlier
in this chapter.
3.
Remove the access panel. Refer to “Server Access Panel” earlier in this chapter.
2-22
HP ProLiant DL360 Generation 3 Server Maintenance and Service Guide
HP CONFIDENTIAL
Codename: Introv-ERTL Part Number: 293948-005 Last Saved On: 2/27/04 2:49 PM