HP PageWide 377 User Guide - Page 35

To connect the product to a wireless network manually, Locate the WPS PIN.

Page 35 highlights

Push Button method 1. On the control panel, press and hold on the printer for more than three seconds to start WPS push mode. The indicator starts blinking. 2. Press the WPS button on your router. The product begins a timer for approximately two minutes while a wireless connection is established. PIN method 1. Locate the WPS PIN. a. Open the control panel dashboard (swipe the dashboard tab at the top of any screen downward, or touch the dashboard area on the home screen). b. On the control panel dashboard, touch . c. Touch Network Setup, and then touch Wireless Settings. d. Touch Wi-Fi Protected Setup, and then touch PIN. 2. On the control panel, press and hold on the printer for more than three seconds to start WPS push mode. The indicator starts blinking. 3. Open the configuration utility or software for the wireless router or wireless access point, and then enter the WPS PIN. NOTE: For more information about using the configuration utility, see the documentation provided with the router or wireless access point. 4. Wait for about two minutes. If the printer connects successfully, the indicator stops blinking but remains lit. To connect the product to a wireless network manually During the first 120 minutes of product setup, or after resetting the product's network defaults (and without a network cable attached to the product), the product's wireless radio will broadcast a wireless setup network for the product. The name of this network is "HP-Setup-xx-[product name]". NOTE: The "xx" in the network name is the last two characters of the product's MAC address. The product name is HP PageWide MFP 377dw . 1. From a wireless enabled product, connect to the setup network for the device. 2. Open a web browser while connected to this setup network, and open the HP Embedded Web Server (EWS) using the following IP address. ● 192.168.223.1 3. Find the Wireless Setup Wizard in the EWS and follow the instructions to manually connect the product. NOTE: The product uses Automatic DHCP by default. ENWW Connect the product to a computer or a network 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203

Push Button method
1.
On the control panel, press and hold
on the printer for more than three seconds to start WPS push
mode. The
indicator starts blinking.
2.
Press the WPS button on your router.
The product begins a timer for approximately two minutes while a wireless connection is established.
PIN method
1.
Locate the WPS PIN.
a.
Open the control panel dashboard (swipe the dashboard tab at the top of any screen downward, or
touch the dashboard area on the home screen).
b.
On the control panel dashboard, touch
.
c.
Touch
Network Setup
, and then touch
Wireless Settings
.
d.
Touch
Wi-Fi Protected Setup
, and then touch
PIN
.
2.
On the control panel, press and hold
on the printer for more than three seconds to start WPS push
mode. The
indicator starts blinking.
3.
Open the configuration utility or software for the wireless router or wireless access point, and then enter
the WPS PIN.
NOTE:
For more information about using the configuration utility, see the documentation provided
with the router or wireless access point.
4.
Wait for about two minutes. If the printer connects successfully, the
indicator stops blinking but
remains lit.
To connect the product to a wireless network manually
During the first 120 minutes of product setup, or after resetting the product's network defaults (and without a
network cable attached to the product), the product's wireless radio will broadcast a wireless setup network
for the product.
The name of this network is “HP-Setup-xx-[product name]”.
NOTE:
The “xx” in the network name is the last two characters of the product's MAC address. The product
name is HP PageWide MFP 377dw .
1.
From a wireless enabled product, connect to the setup network for the device.
2.
Open a web browser while connected to this setup network, and open the HP Embedded Web Server
(EWS) using the following IP address.
192.168.223.1
3.
Find the Wireless Setup Wizard in the EWS and follow the instructions to manually connect the product.
NOTE:
The product uses Automatic DHCP by default.
ENWW
Connect the product to a computer or a network
19