HP Pavilion g4-2000 HP Pavilion g4 Notebook PC - Maintenance and Service Guide - Page 46

Installing a hard drive without an operating system, Memory module, IMPORTANT, WARNING, CAUTION

Get HP Pavilion g4-2000 PDF manuals and user guides View all HP Pavilion g4-2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

After the setup has been completed, reinstall any applications and restore any data that you backed up. If you need further assistance, call 1-800-474-6836 (1 800-HP Invent). Installing a hard drive without an operating system NOTE: If your hard drive was shipped without an operating system installed, you will need to reinstall it using the system recovery discs. To install the operating system, refer to the instructions included with your system recovery discs or that are available from the support site (http://www.hp.com/go/contactHP). IMPORTANT: Do not turn off the computer during the initial setup process. Allow the system recovery process to complete to ensure that everything that is necessary to operate the computer is installed properly. The system recovery process takes approximately 3 hours to complete. When the system recovery is complete, the computer reboots and the Windows Setup screen displays. After the operating system has been installed, reinstall any applications and restore any data that you backed up. If you need further assistance, call 1-800-474-6836 (1 800-HP Invent). Memory module WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module. CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning any procedure, ensure that you are discharged of static electricity by touching a grounded metal object. NOTE: To use a dual-channel configuration with a second memory module, be sure that both memory modules are identical. Description 4 GB (PC3, 12800, 1600 MHz) 2 GB (PC3, 12800, 1600 MHz) Spare part number 641369-001 652972-001 Before removing a memory module, follow these steps: CAUTION: To prevent information loss or an unresponsive system, shut down the computer before adding or replacing memory modules. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation. 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 31). 5. Remove the service door (see Service door on page 32). 38 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
After the setup has been completed, reinstall any applications and restore any data that you backed
up.
If you need further assistance, call 1-800-474-6836 (1 800-HP Invent).
Installing a hard drive without an operating system
NOTE:
If your hard drive was shipped without an operating system installed, you will need to
reinstall it using the system recovery discs. To install the operating system, refer to the instructions
included with your system recovery discs or that are available from the support site
(
go/contactHP
).
IMPORTANT:
Do not turn off the computer during the initial setup process. Allow the system
recovery process to complete to ensure that everything that is necessary to operate the computer is
installed properly.
The system recovery process takes approximately 3 hours to complete. When the system recovery is
complete, the computer reboots and the Windows Setup screen displays. After the operating system
has been installed, reinstall any applications and restore any data that you backed up.
If you need further assistance, call 1-800-474-6836 (1 800-HP Invent).
Memory module
WARNING!
To reduce the risk of electric shock and damage to the equipment, unplug the power
cord and remove all batteries before installing a memory module.
CAUTION:
Electrostatic discharge (ESD) can damage electronic components. Before beginning
any procedure, ensure that you are discharged of static electricity by touching a grounded metal
object.
NOTE:
To use a dual-channel configuration with a second memory module, be sure that both
memory modules are identical.
Description
Spare part number
4 GB (PC3, 12800, 1600 MHz)
641369-001
2 GB (PC3, 12800, 1600 MHz)
652972-001
Before removing a memory module, follow these steps:
CAUTION:
To prevent information loss or an unresponsive system, shut down the computer before
adding or replacing memory modules. Do not remove a memory module while the computer is on, in
the Sleep state, or in Hibernation.
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
31
).
5.
Remove the service door (see
Service door
on page
32
).
38
Chapter 4
Removal and replacement procedures