HP Pro SFF 280 G9 Desktop PC Maintenance and Service Guide - Page 30

Optical drive

Get HP Pro SFF 280 G9 Desktop PC PDF manuals and user guides View all HP Pro SFF 280 G9 Desktop PC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

7. Rotate the slot cover retention latch back in place to secure the expansion card. 8. Connect external cables to the installed card, if needed. Connect internal cables to the system board, if needed. 9. If you are not installing a new expansion card, install an expansion slot cover to close the open slot. CAUTION: After removing an expansion card, you must replace it with a new card or expansion slot cover to properly cool internal components during operation. 10. Reassemble and reconfigure the computer, if necessary. Optical drive The optical drive is located in the drive cage. You can remove the optical drive without removing the front bezel or the drive cage. To remove the optical drive, use these procedures. Before removing the optical drive, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 18). 2. Remove the access panel (see Access panel on page 19). Remove the optical drive: 1. Disconnect the power cable (1) and data cable (2) from the rear of the drive. NOTE: When removing the cables, pull the tab or connector instead of the cable itself to avoid damaging the cable. Optical drive 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
7.
Rotate the slot cover retention latch back in place to secure the expansion card.
8.
Connect external cables to the installed card, if needed. Connect internal cables to the system board, if
needed.
9.
If you are not installing a new expansion card, install an expansion slot cover to close the open slot.
CAUTION:
After removing an expansion card, you must replace it with a new card or expansion slot
cover to properly cool internal components during operation.
10.
Reassemble and reconfigure the computer, if necessary.
Optical drive
The optical drive is located in the drive cage. You can remove the optical drive without removing the front
bezel or the drive cage. To remove the optical drive, use these procedures.
Before removing the optical drive, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
18
).
2.
Remove the access panel (see
Access panel
on page
19
).
Remove the optical drive:
1.
Disconnect the power cable
(1)
and data cable
(2)
from the rear of the drive.
NOTE:
When removing the cables, pull the tab or connector instead of the cable itself to avoid
damaging the cable.
Optical drive
23