HP StorageWorks 2/16V HP StorageWorks SAN Switch 2/8V, 2/16V and 2/16N Instal - Page 44

Assembling the inner rails on a SAN Switch with plenum, The components

Page 44 highlights

Installing the SAN Switch b. For the SAN Switch 2/8V, assemble the two inner rails (one on each side) to the switch and plenum using the appropriate number (from step 5 on page 42) of #8-32 x 5/16-inch Phillips pan-head SEMS screws as shown in Figure 11. Note: The plenum is a required part of this installation when the SAN switch 2/8V, SAN switch 2/16V or 2/16N are installed in an HP 9000 or 10000 serires, System/e or comparable EIA cabinet. The plenum allows air to dissipate at the rear of the rack, preventing overheating. If the Plenum is not pre-installed, refer to step b on page 44 for instructions. 1 2 0013a Figure 11: Assembling the inner rails on a SAN Switch with plenum The components in Figure 11 include: 1 Plenum 2 Switch 7. Insert the switch with the attached inner rails into the outer rails. 44 SAN Switch 2/8V, 2/16V and 2/16N Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116

Installing the SAN Switch
44
SAN Switch 2/8V, 2/16V and 2/16N Installation Guide
b.
For the SAN Switch 2/8V, assemble the two inner rails (one on each side)
to the switch and plenum using the appropriate number (from
step 5
on
page 42) of #8-32 x 5/16-inch Phillips pan-head SEMS screws as shown
in
Figure 11
.
Note:
The plenum is a required part of this installation when the SAN switch 2/8V,
SAN switch 2/16V or 2/16N are installed in an HP 9000 or 10000 serires, System/e
or comparable EIA cabinet.
The plenum allows air to dissipate at the rear of the rack, preventing overheating. If the
Plenum is not pre-installed, refer to
step b
on page 44 for instructions.
Figure 11:
Assembling the inner rails on a SAN Switch with plenum
The components in
Figure 11
include:
7.
Insert the switch with the attached inner rails into the outer rails.
1
Plenum
2
Switch
0013a
2
1