Home » HP Manuals » Storage Devices » HP StorageWorks 2/16V » Manual Viewer

HP StorageWorks 2/16V HP StorageWorks SAN Switch 2/8V, 2/16V and 2/16N Instal - Page 95

Facility Requirements, Table 18: Facility Requirements, To ensure correct operation of the switch

View all HP StorageWorks 2/16V manuals

Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Technical Specifications Facility Requirements To ensure correct operation of the switch, the facility where the switch is in use must meet the following requirements shown in Table 18: Table 18: Facility Requirements Type Electrical Thermal Cabinet (when rack-mounted) Requirements Primary AC Input 100-240 VAC, 1.5A, 47-63 Hz (SAN Switch 2/8V) and 100-240 VAC, 2.0A, 47-63 Hz (SAN Switch 2/16V); switch autosenses input voltage Adequate supply circuit, line fusing, and wire size, as specified by the electrical rating on the switch nameplate Circuit protected by a circuit breaker and grounded in accordance with local electrical codes See Table 20 on page 98 for details A minimum air flow of 24 cubic ft/minute available in the immediate vicinity of the switch Ambient air temperature not exceeding 40° C (104° F) while the switch is operating One rack unit in a 19-in. (48.3 cm.) cabinet All equipment in cabinet grounded through a reliable branch circuit connection Additional weight of switch must not exceed the cabinet's weight limits Cabinet must be secured to insure stability in case of unexpected movement, such as an earthquake SAN Switch 2/8V, 2/16V and 2/16N Installation Guide 95

Section	Page
Contents	3
About this Guide	9
Overview	10
Intended Audience	10
Related Documentation	10
Conventions	11
Document Conventions	11
Table 1: Document Conventions	11
Text Symbols	12
Equipment Symbols	12
Rack Stability	14
Getting Help	15
HP Technical Support	15
HP Storage Web site	15
HP Authorized Reseller	15
Overview	17
SAN Switch 2/8V, 2/16V and 2/16N Features	18
SAN Switch 2/8V and 2/16 Switches Comparison	18
SAN Switch Licensing	19
Switch Characteristics	20
Port Side	20
Figure 1: Port Side of SAN Switch 2/8V	20
Table 2: SAN Switch 2/8V port side components	20
Figure 2: Port Side of the SAN Switch 2/16V and 2/16N	21
Table 3: SAN Switch 2/16V and 2/16N port side components	21
Nonport Side of SAN Switch 2/8V, 2/16V and 2/16N	21
ISL Trunking Groups	22
Figure 3: Trunking groups	22
Supported (Optional) Features	23
Optional Hardware Kits	24
Table 4: Orderable Hardware	24
Installing the SAN Switch	25
Items Included with the SAN Switch 2/8V, 2/16V and 2/16N	26
Shipping Carton Contents	27
Figure 4: Shipping carton contents	27
Table 5: Shipping Carton Contents	28
Installation and Safety Considerations	29
Electrical Considerations	29
Environmental Considerations	29
Installing a Stand-Alone SAN Switch 2/8V, 2/16V and 2/16N	31
Installing a SAN Switch 2/8V, 2/16V or 2/16N Into an EIA Cabinet	32
Selecting an Operating Location	32
Cooling Requirements	32
Power Requirements	33
Installing the Switch in a Rack Using the SAN Switch Rack Mount Kit	34
Table 6: Rack Mount Kit rails and rail mounting hardware (Continued)	34
Figure 5: Installing the rear mounting brackets (HP 10000 series or comparable EIA cabinet)	37
Figure 6: Installing the rear mounting brackets (HP System/e rack-left rear upright)	38
Figure 7: Installing the outer rails (HP 10000 series or comparable EIA cabinet)	39
Figure 8: Assembling the outer rails (HP 10000 series or comparable EIA cabinet)	40
Figure 9: Assembling the outer rails (HP System/e cabinet)	41
Table 7: Number of screws required to assemble the inner rails	42
Figure 10: Assembling the inner rails	43
Figure 11: Assembling the inner rails on a SAN Switch with plenum	44
Figure 12: Installing the switch into a rack (HP 10000 series or comparable EIA cabinet)	45
Figure 13: Installing the switch into a rack (HP System/e cabinet)	46
Cabling and Configuring the SAN Switch 2/8V, 2/16V or 2/16N	47
Recommendations for Cable Management	47
Items Required for Installation	48
Configuring the SAN Switch 2/8V, 2/16V and 2/16N	48
Create a Serial Connection	49
Figure 14: Connecting the serial cable	49
Power Up the Switch and Log In	50
Figure 15: Connecting the power cords	50
Set the IP Address	51
Create an Ethernet Connection and Log In	52
Figure 16: Connecting the Ethernet cable	52
Modify the Fibre Channel Domain ID (Optional)	53
Install the SFP Transceivers	54
Connect the Cables	54
Verifying Configuration	55
Backing Up Your Configuration	55
Managing the SAN Switches	57
Powering the Switch On and Off	58
Interpreting LED Activity	59
LED Location	60
Figure 17: SAN Switch 2/8V LED locations	60
Table 8: SAN Switch 2/8V LED Locations	60
Figure 18: SAN Switch 2/16V LED locations	61
Table 9: SAN Switch 2/16V LED Locations	61
LED Patterns	62
System and Power LED Patterns	62
Table 10: System LED Patterns During Normal Operation	62
Port LED Patterns	63
Table 11: Port LED Patterns During Normal Operation (Continued)	63
Ethernet LED Patterns	64
Table 12: Ethernet LED Patterns	64
POST and Boot Specifications	65
POST	65
Boot	65
Interpreting POST Results	66
Backing Up the Configuration and Upgrade Firmware	67
SAN Switch 2/8V, 2/16V and 2/16N Management Features	68
Table 13: Management Options	68
Maintaining the SAN Switch 2/8V, SAN Switch 2/16V and SAN Switch 2/16N	70
Installing an SFP	70
Figure 19: Installing or removing an SFP	71
Removing an SFP	72
Diagnostic Tests	72
Regulatory Compliance Notices	73
FCC EMC Statement (USA)	74
EMC Statement (Canada)	75
EMC Statement (European Union)	76
European Union Notice	77
Germany Noise Declaration	78
VCCI EMC Statement (Japan)	79
RRL EMC Statement (Korea)	80
Laser Safety	81
Battery Replacement Notice	83
Electrostatic Discharge	85
Grounding Methods	86
Technical Specifications	87
Data Transmission Ranges	88
Table 14: Laser Data Transmission Ranges	88
Fibre Channel Port Specifications	89
Serial Port Specifications	90
Power Supply Specifications	91
Table 15: Power Supply Specifications	91
Weight and Physical Dimensions	92
Table 16: Switch specifications	92
Memory Specifications	93
Table 17: Memory Specifications	93
Supported SFPs	94
Facility Requirements	95
Table 18: Facility Requirements	95
Environmental Requirements	96
Table 19: Environmental Requirements	96
Supported HBAs	97
System Specifications	98
Table 20: General Specifications (Continued)	98
Glossary	101
Index	113
A	113
B	113
C	113
D	114
E	114
F	114
G	114
H	114
I	114
L	115
M	115
N	115
O	115
P	115
R	115
S	116
T	116
U	116
V	116
W	116