HP StorageWorks 8/80 Brocade EZSwitchSetup Administrator's Guide v6.2.0 (53-10 - Page 23

Set Switch IP Address screen, are setting up the switch for the first time

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Installing and running the EZSwitchSetup wizard 2 NOTE If you see a caution message saying the IP address is not reachable, always select Yes (the default setting) under Do you want to assign a static IP to the Switch? Selecting No causes EZSwitchSetup to continuously try to establish a Telnet session with the switch, which does not, as yet, have a reachable IP address. If you have previously enabled DHCP on the switch (refer to "Installing and running the EZSwitchSetup wizard"), you may select No. d. Click Next. EZSwitchSetup attempts to log in using default credentials. If you have already changed your admin password, you will be prompted to enter your new password. After the login is processed, the Set Switch IP Address screen is displayed (Figure 9). FIGURE 9 Set Switch IP Address screen 7. Beginning at this step, the steps are the same for both serial and Ethernet connections. If you are setting up the switch for the first time, the addresses shown are not valid. If you click Next with these addresses in place, EZSwitchSetup returns an error screen. To set up IPv4 addresses, edit the address information on the Set Switch IP Address screen to create static addresses appropriate for your LAN connection. To set up IPv6 addresses, enter the IPv6 address and Prefix in the spaces provided. 8. Click Next. 9. Go on to "Confirming IP addresses". EZSwitchSetup Administrator's Guide 11 53-1001193-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
EZSwitchSetup Administrator’s Guide
11
53-1001193-02
Installing and running the EZSwitchSetup wizard
2
NOTE
If you see a caution message saying the IP address is not reachable, always select
Yes
(the default
setting) under
Do you want to assign a static IP to the Switch?
Selecting
No
causes EZSwitchSetup
to continuously try to establish a Telnet session with the switch, which does not, as yet, have a
reachable IP address. If you have previously enabled DHCP on the switch (refer to
“Installing and
running the EZSwitchSetup wizard”
), you may select
No
.
d.
Click
Next
.
EZSwitchSetup attempts to log in using default credentials. If you have already changed
your admin password, you will be prompted to enter your new password. After the login is
processed, the
Set Switch IP Address
screen is displayed (
Figure 9
).
FIGURE 9
Set Switch IP Address screen
7.
Beginning at this step, the steps are the same for both serial and Ethernet connections. If you
are setting up the switch for the first time, the addresses shown are not valid. If you click
Next
with these addresses in place, EZSwitchSetup returns an error screen. To set up IPv4
addresses, edit the address information on the
Set Switch IP Address
screen to create static
addresses appropriate for your LAN connection. To set up IPv6 addresses, enter the
IPv6
address
and
Prefix
in the spaces provided
.
8.
Click
Next
.
9.
Go on to
“Confirming IP addresses”
.