HP StoreOnce 4430 HP D2D Backup System Installation and Configuration guide (E - Page 17

Connecting to the Capacity Upgrade Kit (optional), HP D2D4300 Series Backup System - installation guide

Get HP StoreOnce 4430 PDF manuals and user guides View all HP StoreOnce 4430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Connecting to the Capacity Upgrade Kit (optional) Install the rail kit and expansion module(s) immediately below or above the HP StoreOnce Backup System, as described in the Capacity Upgrade Installation guide supplied with the expansion module. • HP D2D4300 Series Backup System: Up to three expansion shelves may be connected. It is recommended that the configuration shown below is followed. The user is advised to make a record of which shelf serial number is connected to which RAID card and its port for future reference. • HP D2D4100 Series Backup System: Only one expansion shelf may be connected. • HP D2D2500 Series Backup System: This model does not support connection of an expansion shelf. HP D2D4300 Series Backup System WARNING! Daisy-chaining Capacity Upgrade Kits is not supported. Each Capacity Upgrade Kit must be directly connected to one of the RAID cards on the HP D2D4300 Series Backup System. Each kit is supplied with two cables; the longer cable is suitable for connecting lower shelves as shown in the figures below. Make sure you have the correct Capacity Upgrade Kit for your HP StoreOnce Backup System. • HP D2D4324 Backup System Capacity Upgrade Kit: This kit consists of an enclosure with 12 x 2 TB disks and two cables, and is for use with the HP D2D4324 Backup System only. • HP D2D4312/4112 Backup System Capacity Upgrade Kit: This consists of an enclosure with 12 x 1 TB disks and two cables, and is for use with both the HP D2D4112 and the HP D2D4312 Backup System. 1. To ensure correct keying, first connect the supplied cable to the P1 connector on the top I/O module (I/O-A) on the rear of the Capacity Upgrade Kit. NOTE: Always use the P1 connector; do not use the P2 connector. 2. Connect the other end of each cable to the connector on the RAID card. HP D2D4324 Backup System This product has three RAID cards and there are four connectors on each card. Always use the top connector (port 1E) and never connect more than one shelf to the RAID card. Only three expansion shelves may be connected. Connecting to the Capacity Upgrade Kit (optional) 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Connecting to the Capacity Upgrade Kit (optional)
Install the rail kit and expansion module(s) immediately below or above the HP StoreOnce Backup
System, as described in the Capacity Upgrade Installation guide supplied with the expansion
module.
•
HP D2D4300 Series Backup System: Up to three expansion shelves may be connected. It is
recommended that the configuration shown below is followed. The user is advised to make a
record of which shelf serial number is connected to which RAID card and its port for future
reference.
•
HP D2D4100 Series Backup System: Only one expansion shelf may be connected.
•
HP D2D2500 Series Backup System: This model does not support connection of an expansion
shelf.
HP D2D4300 Series Backup System
WARNING!
Daisy-chaining Capacity Upgrade Kits is
not
supported. Each Capacity Upgrade
Kit must be directly connected to one of the RAID cards on the HP D2D4300 Series Backup System.
Each kit is supplied with two cables; the longer cable is suitable for connecting lower shelves as
shown in the figures below.
Make sure you have the correct Capacity Upgrade Kit for your HP StoreOnce Backup System.
•
HP D2D4324 Backup System Capacity Upgrade Kit: This kit consists of an enclosure with 12
x 2 TB disks and two cables, and is for use with the HP D2D4324 Backup System only.
•
HP D2D4312/4112 Backup System Capacity Upgrade Kit: This consists of an enclosure with
12 x 1 TB disks and two cables, and is for use with both the HP D2D4112 and the HP
D2D4312 Backup System.
1.
To ensure correct keying, first connect the supplied cable to the P1 connector on the top I/O
module (I/O-A) on the rear of the Capacity Upgrade Kit.
NOTE:
Always use the P1 connector; do not use the P2 connector.
2.
Connect the other end of each cable to the connector on the RAID card.
HP D2D4324 Backup System
This product has three RAID cards and there are four connectors on each card. Always use
the top connector (port 1E) and never connect more than one shelf to the RAID card. Only
three expansion shelves may be connected.
Connecting to the Capacity Upgrade Kit (optional)
17