HP StoreOnce 4430 HP D2D Backup System Installation and Configuration guide (E - Page 31

Using the iLO2 port

Get HP StoreOnce 4430 PDF manuals and user guides View all HP StoreOnce 4430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Figure 23 System console screen (example shows HP D2D4106/4112) 4. Locate the IP address for the port(s) and make a note of it. 5. In the web browser on the host machine, type in the IP address of the HP StoreOnce Backup System to connect to it. Using the iLO2 port This feature is supported on all HP StoreOnce Backup Systems, which are G2 products (it is not supported on older G1 HP StorageWorks products).The HP StoreOnce Backup System is supplied with the iLO2 Advanced Pack enabled. • The default Name, Administrator Login Name and Password for iLO2 access are provided on the HP StoreOnce Backup System and on a toe tag attached to it. Make a note of these; you will need them to log on to iLO2. • A separate network connection is required to the iLO2 network port on the rear of the HP StoreOnce Backup System (item 1 on the drawings below). This should be used to connect the HP StoreOnce Backup System to the same network as the host that is running the iLO2 management application. • DHCP is the default network setting for iLO2 web page access. If a static address is required, this must be done via a keyboard and monitor connection when the HP StoreOnce Backup System is booted up. (This is done using the POST F8 option. You may need to press a key to see the prompt.) If DHCP is supported, but not preferred, iLO2 access may be configured via the web interface. Discovering the HP StoreOnce Backup System (mandatory) 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Figure 23 System console screen (example shows HP D2D4106/4112)
4.
Locate the IP address for the port(s) and make a note of it.
5.
In the web browser on the host machine, type in the IP address of the HP StoreOnce Backup
System to connect to it.
Using the iLO2 port
This feature is supported on all HP StoreOnce Backup Systems, which are G2 products (it is not
supported on older G1 HP StorageWorks products).The HP StoreOnce Backup System is supplied
with the iLO2 Advanced Pack enabled.
•
The default Name, Administrator Login Name and Password for iLO2 access are provided
on the HP StoreOnce Backup System and on a toe tag attached to it. Make a note of these;
you will need them to log on to iLO2.
•
A separate network connection is required to the iLO2 network port on the rear of the HP
StoreOnce Backup System (item 1 on the drawings below). This should be used to connect
the HP StoreOnce Backup System to the same network as the host that is running the iLO2
management application.
•
DHCP is the default network setting for iLO2 web page access. If a static address is required,
this must be done via a keyboard and monitor connection when the HP StoreOnce Backup
System is booted up. (This is done using the POST F8 option. You may need to press a key
to see the prompt.) If DHCP is supported, but not preferred, iLO2 access may be configured
via the web interface.
Discovering the HP StoreOnce Backup System (mandatory)
31