HP StoreOnce 4430 HP D2D Backup System Installation and Configuration guide (E - Page 40

Fibre Channel configuration

Get HP StoreOnce 4430 PDF manuals and user guides View all HP StoreOnce 4430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Figure 34 Persistent Targets tab (iSCSI) Bound Volumes/Devices tab No configuration is required on the Bound Volumes/Devices tab. Fibre Channel configuration Backup and restore is supported over both Ethernet networks and Fibre Channel SAN. However, the Web Management Interface always requires an Ethernet connection. When using FC to back up hosts, you should still run the Installation wizard to connect to and discover your HP StoreOnce Backup System and must still connect to: • HP D2D4300 Series: LAN port 3 • HP D2D4100 Series: LAN port 1 Fibre Channel connection The HP StoreOnce Backup System is supplied with the correct FC card pre-installed. It does not include FC cables. 1. Connect to the appropriate LAN port. 2. Use a FC Multimode 50/125 (preferred) or 62.5/125 cable to connect the port(s) on the FC card in the HP StoreOnce Backup System to the Fibre Channel Switch. 3. The switch must have a multi-mode transceiver that supports speeds of: • HP D2D4300 Series: 8Gbs (preferred), 4Gbs or 2Gbs • HP D2D4100 Series: 4Gbs (preferred) or 2Gbs 4. Run the Installation wizard , as described in this guide. 5. Run the Web Management Interface and create at least one library device. Be sure to select one of the FC ports in the Port drop-down. For information about the other fields, see the HP StoreOnce Backup System User Guide or online Help. 40 Advanced installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Figure 34 Persistent Targets tab (iSCSI)
Bound Volumes/Devices tab
No configuration is required on the
Bound Volumes/Devices
tab.
Fibre Channel configuration
Backup and restore is supported over both Ethernet networks and Fibre Channel SAN. However,
the Web Management Interface always requires an Ethernet connection. When using FC to back
up hosts, you should still run the Installation wizard to connect to and discover your HP StoreOnce
Backup System and must still connect to:
•
HP D2D4300 Series: LAN port 3
•
HP D2D4100 Series: LAN port 1
Fibre Channel connection
The HP StoreOnce Backup System is supplied with the correct FC card pre-installed. It does not
include FC cables.
1.
Connect to the appropriate LAN port.
2.
Use a FC Multimode 50/125 (preferred) or 62.5/125 cable to connect the port(s) on the FC
card in the HP StoreOnce Backup System to the Fibre Channel Switch.
3.
The switch must have a multi-mode transceiver that supports speeds of:
•
HP D2D4300 Series: 8Gbs (preferred), 4Gbs or 2Gbs
•
HP D2D4100 Series: 4Gbs (preferred) or 2Gbs
4.
Run the Installation wizard , as described in this guide.
5.
Run the Web Management Interface and create at least one library device. Be sure to select
one of the FC ports in the
Port
drop-down. For information about the other fields, see the
HP
StoreOnce Backup System User Guide
or online Help.
40
Advanced installation