HP StoreOnce 4430 HP StoreOnce 2600, 4200 and 4400 Backup system Maintenance a - Page 23

HP SAS expander card, Table 5 Cabling to HP SAS expander card HP StoreOnce 4430/4420 Backup system

Get HP StoreOnce 4430 PDF manuals and user guides View all HP StoreOnce 4430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

1. Power off the HP StoreOnce Backup system. Remove the cover from the HP StoreOnce Backup System, as described in the appropriate HP ProLiant Maintenance and Service guide, and locate the P411 controllers in PCI-e slots 5 and 6. NOTE: The LEDs on the P411 controller card provide diagnostic information when the unit is powered on. For a detailed description of these LEDs, refer to the "HP Smart Arrays for HP ProLiant Servers user guide". 2. Unclip the blue PCIe card retaining latch and remove the PCIe card. 3. Install the new P411 card and check that it is seated properly. Close the blue PCIe card retaining latch. 4. Replace the cover, as described in the appropriate HP ProLiant Maintenance and Service guide, and power on the HP StoreOnce Backup system. 5. Install the SAAP license. a. Reboot the system. b. During the POST screen, when advised, hit any key to see further messages. c. Enter the Smart Array POST ORCA utility by pressing [F8] when details for the P411 card are displayed during the POST messages. d. Select the Manage Licenses option in the Smart Array menu, and then select Install Licenses. e. Enter the licence key previously noted. HP SAS expander card If no disks are showing on the Hardware tree of the StoreOnce Management Console for sa_controller_0, there may be a problem with the HP SAS expander card. The part number for a replacement card is: 468405-001. It must be installed in PCI-e slot 1. Mini-SAS cables (part numbers 493228-005 and 493228-006) connect the expander card to the hard disk drive backplane, as described in the following table. SAS cables are also connected from the motherboard to the SAS expander card NOTE: Tuck the mini-SAS cables to be routed to the backplane into the side of the chassis. Loop the SAS cables to connect to the motherboard in the void. Table 5 Cabling to HP SAS expander card (HP StoreOnce 4430/4420 Backup system) Connect 1 493228-006 mini-SAS cable 2 493228-006 mini-SAS cable 3 493228-005 mini-SAS cable 4 493228-005 mini-SAS cable 5 SAS cable 6 SAS cable From. Port 2C on SAS expander card Port 3C on SAS expander card Port 4C on SAS expander card Port 5C on SAS expander card Connector A (left) on the motherboard Connector B (right) on the motherboard To Bottom right HDD backplane connector Top right HDD backplane connector Bottom left HDD backplane connector Top left HDD backplane connector Port 8C on the SAS expander card Port 9C on the SAS expander card HP SAS expander card 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
1.
Power off the HP StoreOnce Backup system. Remove the cover from the HP StoreOnce Backup
System, as described in the appropriate HP ProLiant Maintenance and Service guide, and
locate the P411 controllers in PCI-e slots 5 and 6.
NOTE:
The LEDs on the P411 controller card provide diagnostic information when the unit
is powered on. For a detailed description of these LEDs, refer to the “HP Smart Arrays for HP
ProLiant Servers user guide”.
2.
Unclip the blue PCIe card retaining latch and remove the PCIe card.
3.
Install the new P411 card and check that it is seated properly. Close the blue PCIe card
retaining latch.
4.
Replace the cover, as described in the appropriate HP ProLiant Maintenance and Service
guide, and power on the HP StoreOnce Backup system.
5.
Install the SAAP license.
a.
Reboot the system.
b.
During the POST screen, when advised, hit any key to see further messages.
c.
Enter the Smart Array POST ORCA utility by pressing [F8] when details for the P411 card
are displayed during the POST messages.
d.
Select the
Manage Licenses
option in the Smart Array menu, and then select
Install Licenses
.
e.
Enter the licence key previously noted.
HP SAS expander card
If no disks are showing on the
Hardware
tree of the StoreOnce Management Console for
sa_controller_0, there may be a problem with the HP SAS expander card.
The part number for a replacement card is: 468405–001. It must be installed in PCI-e slot 1.
Mini-SAS cables (part numbers 493228–005 and 493228–006) connect the expander card to
the hard disk drive backplane, as described in the following table. SAS cables are also connected
from the motherboard to the SAS expander card
NOTE:
Tuck the mini-SAS cables to be routed to the backplane into the side of the chassis. Loop
the SAS cables to connect to the motherboard in the void.
Table 5 Cabling to HP SAS expander card (HP StoreOnce 4430/4420 Backup system)
To
From.
Connect
Bottom right HDD backplane
connector
Port 2C on SAS expander card
493228–006 mini-SAS cable
1
Top right HDD backplane connector
Port 3C on SAS expander card
493228–006 mini-SAS cable
2
Bottom left HDD backplane
connector
Port 4C on SAS expander card
493228–005 mini-SAS cable
3
Top left HDD backplane connector
Port 5C on SAS expander card
493228–005 mini-SAS cable
4
Port 8C on the SAS expander card
Connector A (left) on the
motherboard
SAS cable
5
Port 9C on the SAS expander card
Connector B (right) on the
motherboard
SAS cable
6
HP SAS expander card
23