HP Surestore 28/48-Slot with DLT7000 HP SureStore Fibre Channel SCSI Bridge 21 - Page 41

Changing the Default Settings

Get HP Surestore 28/48-Slot with DLT7000 PDF manuals and user guides View all HP Surestore 28/48-Slot with DLT7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Operating the Fibre Bridge Changing the Default Settings Changing the Default Settings The basic Fibre Bridge configuration assumes there is only one Fibre Bridge included in the system. If this is a DLT installation and more than one Fibre bridge will be installed, or if there is another Fibre Channel device using the same address, you must change the fibre channel address, using the serial port of the Fibre Bridge. Connecting the Serial Cable Using the serial cable is not necessary in most installations. The default settings work in most configurations. Use the serial cable only if one of the following situations occurs: • The default configuration must be changed. • A failure has occurred that requires diagnostic procedures. See "Chapter 4: Troubleshooting." If any of these scenarios occur, attach the serial cable and RJ-11 to DB9 adapter as shown in Figure 3-2 on page 3-6. 1. Plug the RJ-11 connector into the Fibre Bridge. 2. Plug the DB9 adapter into the Com1 or Com2 port of the computer. 3. Verify that the RJ-11 serial cable is properly plugged into the RJ-11 to DB9 adapter. Operating the Fibre Bridge Chapter 3 3- 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Chapter 3
3-5
Operating the Fibre Bridge
Changing the Default Settings
Operating the
Fibre Bridge
Changing the Default Settings
The basic Fibre Bridge configuration assumes there is only one Fibre
Bridge included in the system. If this is a DLT installation and more
than one Fibre bridge will be installed, or if there is another Fibre
Channel device using the same address, you must change the fibre
channel address, using the serial port of the Fibre Bridge.
Connecting the Serial Cable
Using the serial cable is not necessary in most installations. The default
settings work in most configurations. Use the serial cable only if one of
the following situations occurs:
•
The default configuration must be changed.
•
A failure has occurred that requires diagnostic procedures. See
“
Chapter 4: Troubleshooting.
”
If any of these scenarios occur, attach the serial cable and RJ-11 to DB9
adapter as shown in Figure 3-2 on page
3-6.
1.
Plug the RJ-11 connector into the Fibre Bridge.
2.
Plug the DB9 adapter into the Com1 or Com2 port of the computer.
3.
Verify that the RJ-11 serial cable is properly plugged into the RJ-11
to DB9 adapter.