HP Surestore 28/48-Slot with DLT7000 HP SureStore Fibre Channel SCSI Bridge 21 - Page 47

Recon the Fibre Channel Address

Get HP Surestore 28/48-Slot with DLT7000 PDF manuals and user guides View all HP Surestore 28/48-Slot with DLT7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Operating the Fibre Bridge Making Configuration Changes NOTE NOTE Figure 3-5 Reconfigure the Fibre Channel Address Use the Fibre Channel Configuration menu to change from the hard address mode to the soft address mode. The Fibre Bridge default setting is hard addressing, where the address is preset to 71 (0x82). Use this procedure when an additional bridge is installed in a system or to resolve a Fibre Channel device ID conflict. 1. From the Configuration menu (Figure 3-4 on page 3-10), select option 2, Fibre Channel Configuration. 2. To toggle between hard addressing and soft addressing, select option 1. 3. To choose a new address, select option 2 and enter a new address from the table in Figure 3-6 on page 3-12. The "Change ALPA Value" option is not available when the soft address mode has been selected. Fibre Channel Configuration Menu Operating the Fibre Bridge Chapter 3 3- 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Chapter 3
3-11
Operating the Fibre Bridge
Making Configuration Changes
Operating the
Fibre Bridge
Reconfigure the Fibre Channel Address
Use the Fibre Channel Configuration menu to change from the hard
address mode to the soft address mode.
NOTE
The Fibre Bridge default setting is hard addressing, where the address is
preset to 71 (0x82). Use this procedure when an additional bridge is
installed in a system or to resolve a Fibre Channel device ID conflict.
1.
From the Configuration menu (Figure 3-4 on page
3-10), select option
2, Fibre Channel Configuration.
2.
To toggle between hard addressing and soft addressing, select option
1.
3.
To choose a new address, select option 2 and enter a new address from
the table in Figure 3-6 on page
3-12.
NOTE
The
“
Change ALPA Value
”
option is not available when the soft address
mode has been selected.
Figure 3-5
Fibre Channel Configuration Menu