HP TouchSmart tx2-1109au HP TouchSmart tx2 Notebook PC - Maintenance and Servi - Page 49

straight up to remove it from the hard drive., Lift the bracket

Get HP TouchSmart tx2-1109au PDF manuals and user guides View all HP TouchSmart tx2-1109au manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

4. Remove the hard drive cover. NOTE: The hard drive cover is included in the Plastics Kit, spare part number 487926-001. 5. Grasp the Mylar tab (1) on the hard drive and lift the hard drive to disconnect it from the system board. 6. Remove the hard drive (2) from the hard drive bay. 7. If it is necessary to remove the hard drive bracket and connector, remove the two Phillips PM3.0×3.0 hard drive bracket screws (1) from each side of the hard drive. 8. Lift the bracket (2) straight up to remove it from the hard drive. 9. Remove the connector (3) from the hard drive. Reverse this procedure to reassemble and install the hard drive. Component replacement procedures 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
4.
Remove the hard drive cover.
NOTE:
The hard drive cover is included in the Plastics Kit, spare part number 487926-001.
5.
Grasp the Mylar tab
(1)
on the hard drive and lift the hard drive to disconnect it from the
system board.
6.
Remove the hard drive
(2)
from the hard drive bay.
7.
If it is necessary to remove the hard drive bracket and connector, remove the two Phillips
PM3.0×3.0 hard drive bracket screws
(1)
from each side of the hard drive.
8.
Lift the bracket
(2)
straight up to remove it from the hard drive.
9.
Remove the connector
(3)
from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
Component replacement procedures
41