Honeywell 3800LR-12 User Manual - Page 47

Serial Trigger Time Out, Manual Trigger, Low Power, Low Power Time Out, Automatic Trigger

Get Honeywell 3800LR-12 PDF manuals and user guides View all Honeywell 3800LR-12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Serial Trigger Time Out: Use this selection to set a time out (in quarter seconds) of the scanner's trigger when using serial commands to trigger the scanner. Once the scanner has timed out, it must be triggered again either serially or manually. After scanning the Serial Trigger Time Out bar code, set the time out duration (from 0-1200 quarter seconds) by scanning digits from the inside back cover, then scanning Save. Default = 0 (infinite, or no time out). Serial Trigger Time Out Manual Trigger, Low Power: The scanner "sleeps," using only 30 milliamps, until the trigger is pulled. When the trigger is pulled, the scanner wakes up and operates at reduced power until there is no triggering for the time set with the Low Power Time Out bar code. There is a short delay in operation when the scanner is first triggered, but there is no delay when operating in low power mode. Manual Trigger, Low Power Note: Manual Trigger, Low Power cannot be used with keyboard wedge applications. Low Power Time Out: Scan the Low Power Time Out bar code to change the time out duration. Then scan the time out duration (from 0-300 seconds) from the inside back cover, and Save. Default = 2 minutes. Note: If you make an error while scanning the digits (before scanning Save), scan Discard on the back cover, scan the Lower Power Time Out bar code, scan the correct digits, then Save again. Low Power Time Out Automatic Trigger: The scanner scans continuously at full power. Default for 3900. Automatic Trigger 3800/3900 User's Guide 3 - 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
3800/3900 User’s Guide
3 - 5
Serial Trigger Time Out:
Use this selection to set a time out (in quarter
seconds) of the scanner’s trigger when using serial commands to trigger the
scanner.
Once the scanner has timed out, it must be triggered again either
serially or manually.
After scanning the Serial Trigger Time Out bar code, set the
time out duration (from 0-1200 quarter seconds) by scanning digits from the
inside back cover, then scanning
Save
.
Default = 0 (infinite, or no time out).
Manual Trigger, Low Power:
The scanner “sleeps,” using only 30 milliamps,
until the trigger is pulled.
When the trigger is pulled, the scanner wakes up and
operates at reduced power until there is no triggering for the time set with the Low
Power Time Out bar code.
There is a short delay in operation when the scanner
is first triggered, but there is no delay when operating in low power mode.
Note:
Manual Trigger, Low Power cannot be used with keyboard wedge
applications.
Low Power Time Out:
Scan the Low Power Time Out bar code to change the
time out duration.
Then scan the time out duration (from 0-300 seconds) from
the inside back cover, and
Save
.
Default = 2 minutes.
Note:
If you make an error while scanning the digits (before scanning Save),
scan Discard on the back cover, scan the Lower Power Time Out bar
code, scan the correct digits, then Save again.
Automatic Trigger:
The scanner scans continuously at full power.
Default for
3900
.
Serial Trigger Time Out
Manual Trigger, Low Power
Low Power Time Out
Automatic Trigger