Honeywell 3800LR-12 User Manual - Page 60

Other Programming Selections, Data Format Editor Commands, Send Commands - stand

Get Honeywell 3800LR-12 PDF manuals and user guides View all Honeywell 3800LR-12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Note: The wildcard for all terminal types is 099. Step 4. Code I.D. On page 4-5, find the symbology to which you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart. Step 5. Length Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length from the Programming Chart. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.) Step 6. Editor Commands Refer to the Format Editor Commands Chart (page 5-2). Scan the symbols that represent the command you want to enter. 94 alphanumeric characters may be entered for each symbology data format. Step 7. Scan Save to save your entries. Other Programming Selections • Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0. If you are clearing an alternate format, scan 1, 2, or 3, depending on the alternate format you are clearing. Scan the Terminal Type (refer to the Supported Terminals Chart on page 2-3), Code I.D. and the length of the format you want to delete. That length data format for that symbology is deleted and all other formats are unaffected. • Save This exits, saving any Data Format changes. • Discard This exits without saving any Data Format changes. Data Format Editor Commands Send Commands F1 Send all characters followed by "xx" key or function code, starting from current cursor position. Syntax = F1xx (xx stands for the hex value for an ASCII code, see Decimal to Hex to ASCII Conversion chart, page 4-6.) F2 Send "nn" characters followed by "xx" key or function code, starting from current cursor position. Syntax = F2nnxx (nn stands for the numeric value (00-99) for the number of characters and xx stands for the hex value for an ASCII code. See Decimal to Hex to ASCII Conversion chart, page 4-6.) F3 Send up to but not including "ss" character (Search and Send) starting from current cursor position, leaving cursor pointing to "ss" character followed by "xx" key or function code. Syntax = F3ssxx (ss and xx both stand for the hex values for ASCII codes, see Decimal to Hex to ASCII Conversion chart, page 4-6.) 5 - 2 3800/3900 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
5 - 2
3800/3900 User’s Guide
Note:
The wildcard for all terminal types is 099.
Step 4.
Code I.D.
On
page 4-5
, find the symbology to which you want to apply the data
format.
Locate the Hex value for that symbology and scan the 2 digit
hex value from the Programming Chart.
Step 5.
Length
Specify what length (up to 9999 characters) of data will be acceptable
for this symbology.
Scan the four digit data length from the Program-
ming Chart.
(Note: 50 characters is entered as 0050.
9999 is a univer-
sal number, indicating all lengths.)
Step 6.
Editor Commands
Refer to the Format Editor Commands Chart (
page 5-2
).
Scan the sym-
bols that represent the command you want to enter.
94 alphanumeric
characters may be entered for each symbology data format.
Step 7.
Scan
Save
to save your entries.
Other Programming Selections
•
Clear One Data Format
This deletes one data format for one symbology.
If you are clearing the
primary format, scan
0
.
If you are clearing an alternate format, scan
1
,
2
, or
3
, depending on the alternate format you are clearing.
Scan the Terminal
Type (refer to the Supported Terminals Chart on
page 2-3
), Code I.D. and the
length of the format you want to delete.
That length data format for that
symbology is deleted and all other formats are unaffected.
•
Save
This exits, saving any Data Format changes.
•
Discard
This exits without saving any Data Format changes.
Data Format Editor Commands
Send Commands
F1
Send all characters followed by “xx” key or function code, starting from cur-
rent cursor position.
Syntax = F1xx
(xx stands for the hex value for an
ASCII code, see Decimal to Hex to ASCII Conversion chart,
page 4-6
.)
F2
Send “nn” characters followed by “xx” key or function code, starting from
current cursor position.
Syntax = F2nnxx
(nn stands for the numeric value
(00-99) for the number of characters and xx stands for the hex value for an
ASCII code.
See Decimal to Hex to ASCII Conversion chart,
page 4-6
.)
F3
Send up to but not including “ss” character (Search and Send) starting from
current cursor position, leaving cursor pointing to “ss” character followed by
“xx” key or function code.
Syntax = F3ssxx
(ss and xx both stand for the
hex values for ASCII codes, see Decimal to Hex to ASCII Conversion chart,
page 4-6
.)