Honeywell WAVE2EX Setup Guide - Page 22
Primary Subs Account No., Secondary Subs Account No., Field 46, Follow Me Reminder Phone Number, - ademco manual
UPC - 781410215504
View all Honeywell WAVE2EX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
LYNXR-I Installation and Setup Guide Data Field Descriptions All four digits of the Subscriber Account number must be entered in Fields ✻43 and ✻44. If ten-digit format is selected in ✻48 (option 5), all ten digits of the Subscriber Account number must be entered. Fields ✻43 and ✻44: Enter [✻] as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as the first digit of a 4-digit account number for Nos. 0000-0999. Enter [✻] as the fifth digit if a 4-digit account number (for 3+1, CID®) is used. Exit field by pressing [✻] if only 3 digits are used. To clear entries from field, press ✻43✻ or ✻44✻. See blank Programming Form for examples of account number entries. If using the paging feature, do not enter a leading 0 in the subscriber account number, and do not use digits A-F anywhere in the number. Some paging systems provide voice mail capability, which is activated by a leading 0 in the message. Enter digits 0-9; # +11=B; # +12=C; # +13=D; # +14=E; or # +15=F. ✻43 ✻44 Primary Subs Account No. Enter a four or ten digit account number. Secondary Subs Account No. Enter a four or ten digit account number. Enter the primary subscriber account number. To clear entries from field, press ✻43✻. Enter the secondary subscriber account number. To clear entries from field, press ✻44✻. Field 46: Enter up to 24 digits. Do not fill unused spaces. Enter 0-9, #+11 for '*'; #+12 for'#'; #+13 for a pause (2 seconds). ✻46 "Follow Me Reminder" Phone Number Enter up to 24 digits. ✻47 Phone System Select Central Station No WATS WATS Pulse 0 = No Speaker Phone 2 = No Speaker Phone Dialing Mode Tone Pulse 1 = No Speaker Phone 4 = With Speaker Phone 3 = No Speaker Phone 6 = With Speaker Phone Tone 5 = With Speaker Phone 7 = With Speaker Phone This option allows the user to schedule a time driven message. When activated the system will dial the phone number programmed and deliver a voice message (custom words 72, 73 and 74). This option is only supported when the pager or follow me feature is enabled in field ✻49 (option 6-9 or 10-13). If using the Follow Me Reminder feature, enter the phone number here. If fewer than 24 digits are entered, exit by pressing [✻]. To clear entries from the field press ✻46✻. The telephone message can be terminated (acknowledged) by pressing any key on the telephone keypad. Pressing any key on the local LYNXR-I keypad will terminate (acknowledge) both the follow me and the local reminder announcements. Note: The follow me reminder announcement will be terminated if any other event requires the system to dial out or if an audible alarm has occurred. This option is used to enter the correct type of phone dialing (pulse or tone), and to select the correct WATS line option for the Central Station. This option is used to activate the Speaker Phone option. Note: If using pulse dialing, you must enter the numbers slowly in order to allow the pulse dialer time to operate. ✻48 Report Format for Primary/Secondary Primary Secondary See choices below See choices below 0 = 3+1; 4+1 ADEMCO Low Speed Standard 1 = 3+1; 4+1 Radionics Standard 2 = 4+2 ADEMCO Low Speed Standard 3 = 4+2 Radionics Standard 5 = ADEMCO Contact ID® Reporting with 10-digit subscriber account number 6 = 4+2 ADEMCO Express 7 = ADEMCO Contact ID® Reporting with 4-digit subscriber account number 8 = 3+1; 4+1 ADEMCO Low Speed Expanded 9 = 3+1; 4+1 Radionics Expanded Enter ✻ as the 4th digit of ✻43 through ✻44, if 3+1 dialer reporting is to be used. (For an explanation of these formats, see the System Communication section of this manual.) Notes: (1) The maximum number of alarm and alarm restore reports during one armed period is determined by field ✻92. (2) If Option 5 is selected a 10-digit account number must be entered in Fields ✻43 or ✻44. (3) Option 5 or 7 (ADEMCO Contact ID® Reporting) must be selected for AVM. - 22 -