Honeywell WAVE2EX Setup Guide - Page 25

Restore Report Codes

Get Honeywell WAVE2EX - Ademco Two Tone Siren PDF manuals and user guides
UPC - 781410215504
View all Honeywell WAVE2EX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

✻63 ✻64 ✻65 ✻66 Low Battery Report Code (See notes above) Test Report Code (See notes above) Open Report Code (See notes above) Arm AWAY/STAY Report Code (See notes above) ✻67 ✻68 RF transmitter Low Batt. Report Code (See notes above) Cancel Report Code (See notes above) RESTORE REPORT CODES (✻70-✻76) ✻70 Alarm Restore Report Code, 1st Digit (See notes above) ✻71 ✻72 ✻73 ✻74 ✻75 ✻76 Trouble Restore Report Code (See notes above) Bypass Restore Report Code (See notes above) AC Restore Report Code (See notes above) Low Battery Restore Report Code (See notes above) RF Transmitter Low Batt. Restore Code (See notes above) Test Restore Report Code (See notes above) LYNXR-I Installation and Setup Guide Data Field Descriptions This will be sent when a low battery condition exists in the system's standby battery. This is sent periodically to test that the communicator and phone lines are operational (frequency of report is selected in field ✻51). This is sent upon disarming of the system. 2nd digit = user number, if expanded or 4+2 reporting is selected. This option allows for independent programming of AWAY and STAY reports. 2nd digit of report is user number if expanded or 4+2 reporting is selected. NOTE: OPEN reports are not sent if the associated closing report is not enabled. This is sent in the event that a wireless transmitter low battery condition exists. This is sent upon disarming of the system after an alarm condition was reported. Sent when the zone that caused an alarm is restored to its nonfaulted condition. 2nd digit is automatically sent as the 2nd digit of the zone alarm report code programmed in field ✻56, if expanded or 4+2 reporting is selected. Sent when a trouble in a zone is restored. Sent when a zone that has been bypassed is unbypassed. Sent when AC power has been restored after an AC power outage. Sent when a system low battery condition is restored to normal. Sent when a transmitter that previously sent in a "low battery" message has sent a message indicating it no longer has a low battery condition. Sent when the test mode is exited. A restore code entered here will cause a restore message to be sent when Test mode is exited. - 25 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
LYNXR-I Installation and Setup Guide
- 25 -
Data Field Descriptions
✻
63
Low Battery Report Code
(See notes above)
This will be sent when a low battery condition exists in the
system’s standby battery.
✻
64
Test Report Code
(See notes above)
This is sent periodically to test that the communicator and
phone lines are operational (frequency of report is selected in
field
✻
51).
✻
65
Open Report Code
(See notes above)
This is sent upon disarming of the system. 2nd digit = user
number, if expanded or 4+2 reporting is selected.
✻
66
Arm AWAY/STAY Report Code
(See notes above)
This option allows for independent programming of AWAY and
STAY reports. 2nd digit of report is user number if expanded or
4+2 reporting is selected.
NOTE: OPEN reports are not sent if the associated closing
report is not enabled.
✻
67
RF transmitter Low Batt. Report Code
(See notes above)
This is sent in the event that a wireless transmitter low battery
condition exists.
✻
68
Cancel Report Code
(See notes above)
This is sent upon disarming of the system after an alarm
condition was reported.
RESTORE REPORT CODES (
✻
70–
✻
76)
✻
70
Alarm Restore Report Code, 1st Digit
(See notes above)
Sent when the zone that caused an alarm is restored to its non-
faulted condition. 2nd digit is automatically sent as the 2nd digit
of the zone alarm report code programmed in field
✻
56, if
expanded or 4+2 reporting is selected.
✻
71
Trouble Restore Report Code
(See notes above)
Sent when a trouble in a zone is restored.
✻
72
Bypass Restore Report Code
(See notes above)
Sent when a zone that has been bypassed is unbypassed.
✻
73
AC Restore Report Code
(See notes above)
Sent when AC power has been restored after an AC power
outage.
✻
74
Low Battery Restore Report Code
(See notes above)
Sent when a system low battery condition is restored to normal.
✻
75
RF Transmitter Low Batt. Restore Code
(See notes above)
Sent when a transmitter that previously sent in a “low battery” message
has sent a message indicating it no longer has a low battery condition.
✻
76
Test Restore Report Code
(See notes above)
Sent when the test mode is exited. A restore code entered here will cause
a restore message to be sent when Test mode is exited.