Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 310 » Manual Viewer

Husqvarna AUTOMOWER 310 Owner Manual - Page 23

After the installation of the product, To do a visual check of the charging station

View all Husqvarna AUTOMOWER 310 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Note: Make sure that you can see the ends of the boundary wire or the guide wire through the transparent area of the coupler. 5. Push the button on the coupler with an adjustable pliers. Note: Some models require a factory PIN code before the selection of personal PIN code. Note: Use the MEMO page at the beginning of the manual to make a note of the PIN code. Introduction on page 3. 6. Put the boundary wire or the guide wire into position with stakes. 3.8 After the installation of the product 3.8.1 To do a visual check of the charging station 1. Make sure that the indicator LED lamp on the charging station has a green light. 2. If the indicator LED lamp does not have a green light, do a check of the installation. Refer to Indicator lamp in the charging station on page 47 and To install the charging station on page 21. 3.8.2 To do the basic settings Before you start the product for the first time, you must do the basic settings and calibrate the product. 1. Push the STOP button. 2. Set the Main switch to 1. 3. Push the arrow buttons and the OK button. Select language, country, date, time and set a PIN code. Note: It is not possible to use 0000 as PIN code. 4. Put the product in the charging station. 5. Push the START button and close the hatch. The product then moves away from the charging station and stops, while it calibrates some of the product settings. 3.9 To do the product settings The product has factory settings but the settings can be adapted to each work area. 3.9.1 To get access to the menu 1. Push the STOP button. 2. Enter the PIN code on the keypad. 3. Push the MENU button. 3.9.2 To do the timer settings 3.9.2.1 To calculate the timer setting 1. Calculate the dimension of your lawn in m2 / yd2. 2. Divide the m2 / yd2 of the lawn with the approximate operation capacity. Refer to table below. 3. The result is equal to the number of hours that the product must operate each day. Note: The operation capacity is approximate and timer settings can be adjusted. Model Approximate operation capacity, m2/h / yd2 /h Automower® 310 56 / 0.01 Automower® 315 68 / 0.02 Automower® 315X 73 / 0.02 Example: A lawn of 500 m2 / 600 yd2, cut with a Automower® 310. 1220 - 001 - 08.07.2019 Installation - 23

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	6
Symbols on the battery	6
Menu structure overview - 1	8
Menu structure overview - 2	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To set the corridor width of the boundary wire	19
To examine where to put the guide wire	19
To set the corridor width of the guide wire	20
Work area examples	20
Installation of the product	21
To install the charging station	21
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
To do the product settings	23
To get access to the menu	23
To do the timer settings	23
To calculate the timer setting	23
To set the timer	24
To copy the timer setting	24
To reset the timer setting	24
Security level	24
To set the security level	24
To change the PIN-code	25
To change the length of the alarm	25
To change the length of the time lock	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Lawn Coverage	25
To disable the GPS Assisted Navigation	26
To enable the GPS Assisted Navigation	26
To set the Lawn coverage function	26
To do a test of the Lawn coverage function	27
To measure the distance from the charging station	27
To disable or enable the Lawn coverage function	27
To reset the Lawn coverage settings	27
Methods for the product to find the charging station	27
To set how the product finds the charging station	27
To do a test of the guide wire	28
To do a test of the boundary wire	28
To change the signal range of the charging station	28
To set the exit angles	28
To set the reversing distance	28
To set the Drive Past Wire function	29
Settings	29
Profiles	29
To save settings to a profile	29
To change the name of a profile	29
To use a profile	29
To connect a new charging station to a profile	29
ECO mode	29
Spiral Cutting	30
To set the level of Spiral Cutting	30
Slope control	30
To disable the Slope control	30
To set the time & date	30
To set the language	30
To set the country	30
To reset all user settings	30
The About menu	30
Accessories	31
Information	31
Automower® Connect app	31
To install the Automower® Connect app	31
Automower® Connect@Home (Automower® 310/315)	31
To pair Connect@Home and the product	31
To remove paired accounts	31
Automower® Connect	31
To pair Automower® Connect and the product	31
To enable the GeoFence function	32
To set a new center point for the Geofence function	32
To set the GeoFence level of sensitivity	32
To use the SMS function	32
Network	32
APN settings	32
Headlights	32
To set the schedule for the headlights	32
To set the Flashes when fault function	32
To avoid collisions with the mower house	33
Connectivity	33
Automower® Direct	33
To start to use Automower® Direct	33
Husqvarna Fleet Services™	33
To connect to the product with Husqvarna Fleet Services	33
Operation	34
Main switch	34
Start	34
Operating mode - Start	34
Main area	34
Secondary area	34
Override timer	35
Spot cutting (Automower® 315/315X)	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start on next timer	35
To stop the product	35
To switch off the product	35
Timer and Standby	35
Example 1	36
Example 2	36
To charge the battery	36
Adjust the cutting height	37
To adjust the cutting height	37
Maintenance	38
Introduction - maintenance	38
Clean the product	38
Chassis and blade disc	38
Chassis	38
Wheels	38
Cover	38
Charging station	38
Replace the blades	39
To replace the blades	39
Battery	39
Winter service	40
Troubleshooting	41
Introduction - troubleshooting	41
Fault messages	41
Information messages	46
Indicator lamp in the charging station	47
Symptoms	48
Find breaks in the loop wire	49
Transportation, storage and disposal	52
Transportation	52
Storage	52
Disposal	52
To remove the battery	52
Technical data	53
Technical data	53
Registered trademarks	55
Warranty	56
Warranty terms	56
Applicable to US/CA market	57
Supplier's Declaration of Conformity	57

Match case Limit results 1 per page

Note:

Make sure that you can see the ends

of the boundary wire or the guide wire

through the transparent area of the coupler.

Push the button on the coupler with an

adjustable pliers.

Put the boundary wire or the guide wire into

position with stakes.

3.8 After the installation of the product

3.8.1 To do a visual check of the charging

station

Make sure that the indicator LED lamp on

the charging station has a green light.

If the indicator LED lamp does not have a

green light, do a check of the installation.

Refer to

Indicator lamp in the charging

station on page 47

and

To install the

charging station on page 21

3.8.2 To do the basic settings

Before you start the product for the first time, you

must do the basic settings and calibrate the

product.

Push the

STOP

button.

Set the

Main switch

to 1.

Push the

arrow

buttons and the

button.

Select

language, country, date, time

and set

a PIN code.

Note:

It is not possible to use 0000 as PIN

code.

Put the product in the charging station.

Push the

START

button and close the hatch.

Note:

Some models require a factory PIN code

before the selection of personal PIN code.

Note:

Use the MEMO page at the beginning of

the manual to make a note of the PIN code.

Introduction on page 3

The product then moves away from the charging

station and stops, while it calibrates some of the

product settings.

3.9 To do the product settings

The product has factory settings but the settings

can be adapted to each work area.

3.9.1 To get access to the menu

Push the

STOP

button.

Enter the PIN code on the keypad.

Push the

button.

3.9.2 To do the timer settings

3.9.2.1 To calculate the timer setting

Calculate the dimension of your lawn in m

Divide the m

/ yd

of the lawn with the

approximate operation capacity. Refer to

table below.

The result is equal to the number of hours

that the product must operate each day.

Note:

The operation capacity is approximate and

timer settings can be adjusted.

Model

Approximate operation ca-

pacity, m

/h / yd

Automower

310

56 / 0.01

Automower

315

68 / 0.02

Automower

315X

73 / 0.02

Example: A lawn of 500 m

/ 600 yd

, cut with a

Automower

310.

1220 - 001 - 08.07.2019

Installation -