Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 310 » Manual Viewer

Husqvarna AUTOMOWER 310 Owner Manual - Page 35

Override timer, Spot cutting (Automower® 315/315X), Operating mode - Park, Park until further notice

View all Husqvarna AUTOMOWER 310 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Note: It is recommended to change the operation selection to Main area before you put the product in the charging station. 4.3.3 Override timer The timer settings can be temporarily overridden by selecting Override timer. It is possible to override the timer for 24 h or 3 days h or days. 4.3.4 Spot cutting (Automower® 315/315X) Spot cutting is useful for quickly mowing an area where the grass has been mown less than in other parts of the garden. Spot cutting means that the product mows in a spiral pattern in order to cut the grass in the area where it was started. When this is done, the product automatically switches back to Main area or Secondary area. The Spot cutting function is activated with the START button. You can select how the product should continue to work once mowing is finished by pressing right arrow button and then selecting On Main area or On Secondary area. 4.4 Operating mode - Park When the PARK button is pressed the following operation selections can be chosen. • Park until further notice • Start again in 3 hours • Start with next timer 4.4.1 Park until further notice The product stays in the charging station until another operating mode is selected by pressing the START button. 4.4.2 Start again in 3 hours The product stays in the charging station for 3 hours and then automatically goes back to the usual operation. This operation selection is applicable when it is necessary to pause operation. 4.4.3 Start on next timer The product stays in the charging station until the next Timer setting permits operation. This operation selection is suitable if one wishes to cancel an ongoing mowing cycle and allow the product to stay in the charging station until the next day. 4.5 To stop the product 1. Press the STOP button on top of the product. The product stops and the blade motor stops. 4.6 To switch off the product 1. Press the STOP button on top of the product. 2. Set the Main switch to position 0. WARNING: Always switch off the product using the main switch if it requires maintenance, or if the product must be moved outside the work area. 4.7 Timer and Standby The product has an inbuilt standby period according to the Standby time table. The standby period provides for instance a good opportunity to water or play games on the lawn. Model Automower® 310 Automower® 315 Automower® 315X Standby time, minimum hours per day 6 2 2 The factory settings for the timer allow the product to operate around the clock 7 days a week. However, the product will not operate during the built-in standby period. 1220 - 001 - 08.07.2019 Operation - 35

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	6
Symbols on the battery	6
Menu structure overview - 1	8
Menu structure overview - 2	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To set the corridor width of the boundary wire	19
To examine where to put the guide wire	19
To set the corridor width of the guide wire	20
Work area examples	20
Installation of the product	21
To install the charging station	21
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
To do the product settings	23
To get access to the menu	23
To do the timer settings	23
To calculate the timer setting	23
To set the timer	24
To copy the timer setting	24
To reset the timer setting	24
Security level	24
To set the security level	24
To change the PIN-code	25
To change the length of the alarm	25
To change the length of the time lock	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Lawn Coverage	25
To disable the GPS Assisted Navigation	26
To enable the GPS Assisted Navigation	26
To set the Lawn coverage function	26
To do a test of the Lawn coverage function	27
To measure the distance from the charging station	27
To disable or enable the Lawn coverage function	27
To reset the Lawn coverage settings	27
Methods for the product to find the charging station	27
To set how the product finds the charging station	27
To do a test of the guide wire	28
To do a test of the boundary wire	28
To change the signal range of the charging station	28
To set the exit angles	28
To set the reversing distance	28
To set the Drive Past Wire function	29
Settings	29
Profiles	29
To save settings to a profile	29
To change the name of a profile	29
To use a profile	29
To connect a new charging station to a profile	29
ECO mode	29
Spiral Cutting	30
To set the level of Spiral Cutting	30
Slope control	30
To disable the Slope control	30
To set the time & date	30
To set the language	30
To set the country	30
To reset all user settings	30
The About menu	30
Accessories	31
Information	31
Automower® Connect app	31
To install the Automower® Connect app	31
Automower® Connect@Home (Automower® 310/315)	31
To pair Connect@Home and the product	31
To remove paired accounts	31
Automower® Connect	31
To pair Automower® Connect and the product	31
To enable the GeoFence function	32
To set a new center point for the Geofence function	32
To set the GeoFence level of sensitivity	32
To use the SMS function	32
Network	32
APN settings	32
Headlights	32
To set the schedule for the headlights	32
To set the Flashes when fault function	32
To avoid collisions with the mower house	33
Connectivity	33
Automower® Direct	33
To start to use Automower® Direct	33
Husqvarna Fleet Services™	33
To connect to the product with Husqvarna Fleet Services	33
Operation	34
Main switch	34
Start	34
Operating mode - Start	34
Main area	34
Secondary area	34
Override timer	35
Spot cutting (Automower® 315/315X)	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start on next timer	35
To stop the product	35
To switch off the product	35
Timer and Standby	35
Example 1	36
Example 2	36
To charge the battery	36
Adjust the cutting height	37
To adjust the cutting height	37
Maintenance	38
Introduction - maintenance	38
Clean the product	38
Chassis and blade disc	38
Chassis	38
Wheels	38
Cover	38
Charging station	38
Replace the blades	39
To replace the blades	39
Battery	39
Winter service	40
Troubleshooting	41
Introduction - troubleshooting	41
Fault messages	41
Information messages	46
Indicator lamp in the charging station	47
Symptoms	48
Find breaks in the loop wire	49
Transportation, storage and disposal	52
Transportation	52
Storage	52
Disposal	52
To remove the battery	52
Technical data	53
Technical data	53
Registered trademarks	55
Warranty	56
Warranty terms	56
Applicable to US/CA market	57
Supplier's Declaration of Conformity	57

Match case Limit results 1 per page

Note:

It is recommended to change the operation

selection to

Main area

before you put the product

in the charging station.

4.3.3 Override timer

The timer settings can be temporarily overridden

by selecting

Override timer

. It is possible to

override the timer for 24 h or 3 days h or days.

4.3.4 Spot cutting (Automower

315/315X)

Spot cutting

is useful for quickly mowing an area

where the grass has been mown less than in

other parts of the garden.

Spot cutting

means that the product mows in a

spiral pattern in order to cut the grass in the area

where it was started. When this is done, the

product automatically switches back to

Main area

Secondary area

The

Spot cutting

function is activated with the

START

button. You can select how the product

should continue to work once mowing is finished

by pressing right

arrow

button and then selecting

On Main area

On Secondary area

4.4 Operating mode - Park

When the

PARK

button is pressed the following

operation selections can be chosen.

•

Park until further notice

•

Start again in 3 hours

•

Start with next timer

4.4.1 Park until further notice

The product stays in the charging station until

another operating mode is selected by pressing

the

START

button.

4.4.2 Start again in 3 hours

The product stays in the charging station for 3

hours and then automatically goes back to the

usual operation. This operation selection is

applicable when it is necessary to pause

operation.

4.4.3 Start on next timer

The product stays in the charging station until the

next Timer setting permits operation. This

operation selection is suitable if one wishes to

cancel an ongoing mowing cycle and allow the

product to stay in the charging station until the

next day.

4.5 To stop the product

Press the

STOP

button on top of the

product.

The product stops and the blade motor stops.

4.6 To switch off the product

Press the

STOP

button on top of the

product.

Set the

Main switch

to position

WARNING:

Always switch off the

product using the main switch if it

requires maintenance, or if the product

must be moved outside the work area.

4.7 Timer and Standby

The product has an inbuilt standby period

according to the Standby time table. The standby

period provides for instance a good opportunity to

water or play games on the lawn.

Model

Standby time, minimum

hours per day

Automower

310

Automower

315

Automower

315X

The factory settings for the timer allow the

product to operate around the clock 7 days a

week. However, the product will not operate

during the built-in standby period.

1220 - 001 - 08.07.2019

Operation -