Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 310 » Manual Viewer

Husqvarna AUTOMOWER 310 Owner Manual - Page 39

Replace the blades, Battery

View all Husqvarna AUTOMOWER 310 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

5.3 Replace the blades WARNING: Use blades and screws of the right type. Husqvarna can only guarantee safety when using original blades. Only replacing the blades and reusing the screw can result in a screw wearing during mowing. The blades can then be propelled from under the body and cause serious injury. Replace worn or damaged parts for safety reasons. Even if the blades are intact, they should be replaced on a regular basis for the best mowing result and low energy usage. All 3 blades and screws must be replaced at the same time to obtain a balanced cutting system. Use Husqvarna original blades embossed with the crowned H-mark logotype, refer to Warranty terms on page 56. 5. Remove each blade and screw. 6. Fasten new blades and screws. 7. Check that the blades can pivot freely. 5.4 Battery WARNING: Only charge the product using a charging station and power supply which is intended for it. Incorrect use may result in electric shock, overheating or leakage of corrosive liquid from the battery. In the event of leakage of electrolyte flush with water and seek medical help if it comes in contact with the eyes etc. 5.3.1 To replace the blades 1. Set the Main switch to position 0. WARNING: Use only original batteries recommended by the manufacturer. Product safety cannot be guaranteed with other batteries. Do not use nonrechargeable batteries. 2. Turn the product upside down. Place the product on a soft and clean surface to avoid scratching the body and the hatch. 3. Rotate the skid plate so that its holes align with the screws for the blade. 4. Remove the 3 screws. Use a manual straight slot or cross-tip screwdriver. CAUTION: The battery must be charged fully before winter storage. If the battery is not fully charged it can be damaged and in certain cases be rendered useless. The charging time can vary depending on, among other factors, the ambient temperature. Below indicates that the battery is getting old and eventually needs replacing: • The operating time for the product is shorter than normal between charges. This leads to more charging cycles than normal, which increases the risk of tracks forming near the charging station. • The product is found standing out on the lawn with Empty battery message. This indicates that the product does not have 1220 - 001 - 08.07.2019 Maintenance - 39

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	6
Symbols on the battery	6
Menu structure overview - 1	8
Menu structure overview - 2	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To set the corridor width of the boundary wire	19
To examine where to put the guide wire	19
To set the corridor width of the guide wire	20
Work area examples	20
Installation of the product	21
To install the charging station	21
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
To do the product settings	23
To get access to the menu	23
To do the timer settings	23
To calculate the timer setting	23
To set the timer	24
To copy the timer setting	24
To reset the timer setting	24
Security level	24
To set the security level	24
To change the PIN-code	25
To change the length of the alarm	25
To change the length of the time lock	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Lawn Coverage	25
To disable the GPS Assisted Navigation	26
To enable the GPS Assisted Navigation	26
To set the Lawn coverage function	26
To do a test of the Lawn coverage function	27
To measure the distance from the charging station	27
To disable or enable the Lawn coverage function	27
To reset the Lawn coverage settings	27
Methods for the product to find the charging station	27
To set how the product finds the charging station	27
To do a test of the guide wire	28
To do a test of the boundary wire	28
To change the signal range of the charging station	28
To set the exit angles	28
To set the reversing distance	28
To set the Drive Past Wire function	29
Settings	29
Profiles	29
To save settings to a profile	29
To change the name of a profile	29
To use a profile	29
To connect a new charging station to a profile	29
ECO mode	29
Spiral Cutting	30
To set the level of Spiral Cutting	30
Slope control	30
To disable the Slope control	30
To set the time & date	30
To set the language	30
To set the country	30
To reset all user settings	30
The About menu	30
Accessories	31
Information	31
Automower® Connect app	31
To install the Automower® Connect app	31
Automower® Connect@Home (Automower® 310/315)	31
To pair Connect@Home and the product	31
To remove paired accounts	31
Automower® Connect	31
To pair Automower® Connect and the product	31
To enable the GeoFence function	32
To set a new center point for the Geofence function	32
To set the GeoFence level of sensitivity	32
To use the SMS function	32
Network	32
APN settings	32
Headlights	32
To set the schedule for the headlights	32
To set the Flashes when fault function	32
To avoid collisions with the mower house	33
Connectivity	33
Automower® Direct	33
To start to use Automower® Direct	33
Husqvarna Fleet Services™	33
To connect to the product with Husqvarna Fleet Services	33
Operation	34
Main switch	34
Start	34
Operating mode - Start	34
Main area	34
Secondary area	34
Override timer	35
Spot cutting (Automower® 315/315X)	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start on next timer	35
To stop the product	35
To switch off the product	35
Timer and Standby	35
Example 1	36
Example 2	36
To charge the battery	36
Adjust the cutting height	37
To adjust the cutting height	37
Maintenance	38
Introduction - maintenance	38
Clean the product	38
Chassis and blade disc	38
Chassis	38
Wheels	38
Cover	38
Charging station	38
Replace the blades	39
To replace the blades	39
Battery	39
Winter service	40
Troubleshooting	41
Introduction - troubleshooting	41
Fault messages	41
Information messages	46
Indicator lamp in the charging station	47
Symptoms	48
Find breaks in the loop wire	49
Transportation, storage and disposal	52
Transportation	52
Storage	52
Disposal	52
To remove the battery	52
Technical data	53
Technical data	53
Registered trademarks	55
Warranty	56
Warranty terms	56
Applicable to US/CA market	57
Supplier's Declaration of Conformity	57

Match case Limit results 1 per page

5.3 Replace the blades

WARNING:

Use blades and screws of

the right type. Husqvarna can only

guarantee safety when using original

blades. Only replacing the blades and

reusing the screw can result in a screw

wearing during mowing. The blades

can then be propelled from under the

body and cause serious injury.

Replace worn or damaged parts for safety

reasons. Even if the blades are intact, they

should be replaced on a regular basis for the best

mowing result and low energy usage. All 3 blades

and screws must be replaced at the same time to

obtain a balanced cutting system. Use

Husqvarna original blades embossed with the

crowned H-mark logotype, refer to

Warranty

terms on page 56

5.3.1 To replace the blades

Set the

Main switch

to position

Turn the product upside down. Place the

product on a soft and clean surface to avoid

scratching the body and the hatch.

Rotate the skid plate so that its holes align

with the screws for the blade.

Remove the 3 screws. Use a manual

straight slot or cross-tip screwdriver.

Remove each blade and screw.

Fasten new blades and screws.

Check that the blades can pivot freely.

5.4 Battery

WARNING:

Only charge the product

using a charging station and power

supply which is intended for it.

Incorrect use may result in electric

shock, overheating or leakage of

corrosive liquid from the battery. In the

event of leakage of electrolyte flush

with water and seek medical help if it

comes in contact with the eyes etc.

WARNING:

Use only original batteries

recommended by the manufacturer.

Product safety cannot be guaranteed

with other batteries. Do not use non-

rechargeable batteries.

CAUTION:

The battery must be

charged fully before winter storage. If

the battery is not fully charged it can

be damaged and in certain cases be

rendered useless.

The charging time can vary depending on,

among other factors, the ambient temperature.

Below indicates that the battery is getting old and

eventually needs replacing:

•

The operating time for the product is shorter

than normal between charges. This leads to

more charging cycles than normal, which

increases the risk of tracks forming near the

charging station.

•

The product is found standing out on the

lawn with

Empty battery

message. This

indicates that the product does not have

1220 - 001 - 08.07.2019

Maintenance -