Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 310 » Manual Viewer

Husqvarna AUTOMOWER 310 Owner Manual - Page 34

Operation, Main switch, Start, Operating mode - Start, Main area, Secondary area, 3.1 Main area

View all Husqvarna AUTOMOWER 310 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

4 Operation 4.1 Main switch WARNING: Read the safety instructions carefully before you start the product. WARNING: Keep your hands and feet away from the rotating blades. Never put your hands or feet close to or under the product when the motor is running. WARNING: Do not use the product when persons, especially children, or animals, are in the work area. 5. Select the desired operating mode. Refer to Operating mode - Start on page 34. 6. Close the hatch within 10 seconds. If the product is parked in the charging station, it will only leave the charging station when the battery is fully charged and if the timer is set to allow the product to operate. Note: Always press the START button before closing the hatch to start the product. If the START button is not pressed, a message beep is heard and the product will not start. • Set the Main switch in the 1 position to start the product. • Set the Main switch in the 0 position when the product is not in use or before any work, inspection or maintenance is being carried out. When the Main switch is set in the 0 position the motors on the product cannot start. 4.2 Start 1. Press the STOP button to open the hatch. 2. Set the main switch to position 1. 3. Enter the PIN code. 4. Press the START button. 4.3 Operating mode - Start When the START button has been pushed the following operation selections can be selected. • Main area • Secondary area • Override timer • Spot cutting 4.3.1 Main area Main area is the standard operating mode where the product mows and charges automatically. 4.3.2 Secondary area In the Secondary area mode, the product operates until the battery is empty. When the battery is empty, the product stops and the message Needs manual charging shows in the product display. Put the product in the charging station to charge the battery. If the product charges in the Secondary area mode, it will fully charge, move out about 50 cm / 20 in. and then stop. This means that the product is charged and prepared to start to cut. 34 - Operation 1220 - 001 - 08.07.2019

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	6
Symbols on the battery	6
Menu structure overview - 1	8
Menu structure overview - 2	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To set the corridor width of the boundary wire	19
To examine where to put the guide wire	19
To set the corridor width of the guide wire	20
Work area examples	20
Installation of the product	21
To install the charging station	21
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
To do the product settings	23
To get access to the menu	23
To do the timer settings	23
To calculate the timer setting	23
To set the timer	24
To copy the timer setting	24
To reset the timer setting	24
Security level	24
To set the security level	24
To change the PIN-code	25
To change the length of the alarm	25
To change the length of the time lock	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Lawn Coverage	25
To disable the GPS Assisted Navigation	26
To enable the GPS Assisted Navigation	26
To set the Lawn coverage function	26
To do a test of the Lawn coverage function	27
To measure the distance from the charging station	27
To disable or enable the Lawn coverage function	27
To reset the Lawn coverage settings	27
Methods for the product to find the charging station	27
To set how the product finds the charging station	27
To do a test of the guide wire	28
To do a test of the boundary wire	28
To change the signal range of the charging station	28
To set the exit angles	28
To set the reversing distance	28
To set the Drive Past Wire function	29
Settings	29
Profiles	29
To save settings to a profile	29
To change the name of a profile	29
To use a profile	29
To connect a new charging station to a profile	29
ECO mode	29
Spiral Cutting	30
To set the level of Spiral Cutting	30
Slope control	30
To disable the Slope control	30
To set the time & date	30
To set the language	30
To set the country	30
To reset all user settings	30
The About menu	30
Accessories	31
Information	31
Automower® Connect app	31
To install the Automower® Connect app	31
Automower® Connect@Home (Automower® 310/315)	31
To pair Connect@Home and the product	31
To remove paired accounts	31
Automower® Connect	31
To pair Automower® Connect and the product	31
To enable the GeoFence function	32
To set a new center point for the Geofence function	32
To set the GeoFence level of sensitivity	32
To use the SMS function	32
Network	32
APN settings	32
Headlights	32
To set the schedule for the headlights	32
To set the Flashes when fault function	32
To avoid collisions with the mower house	33
Connectivity	33
Automower® Direct	33
To start to use Automower® Direct	33
Husqvarna Fleet Services™	33
To connect to the product with Husqvarna Fleet Services	33
Operation	34
Main switch	34
Start	34
Operating mode - Start	34
Main area	34
Secondary area	34
Override timer	35
Spot cutting (Automower® 315/315X)	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start on next timer	35
To stop the product	35
To switch off the product	35
Timer and Standby	35
Example 1	36
Example 2	36
To charge the battery	36
Adjust the cutting height	37
To adjust the cutting height	37
Maintenance	38
Introduction - maintenance	38
Clean the product	38
Chassis and blade disc	38
Chassis	38
Wheels	38
Cover	38
Charging station	38
Replace the blades	39
To replace the blades	39
Battery	39
Winter service	40
Troubleshooting	41
Introduction - troubleshooting	41
Fault messages	41
Information messages	46
Indicator lamp in the charging station	47
Symptoms	48
Find breaks in the loop wire	49
Transportation, storage and disposal	52
Transportation	52
Storage	52
Disposal	52
To remove the battery	52
Technical data	53
Technical data	53
Registered trademarks	55
Warranty	56
Warranty terms	56
Applicable to US/CA market	57
Supplier's Declaration of Conformity	57

Match case Limit results 1 per page

4 Operation

4.1 Main switch

WARNING:

Read the safety

instructions carefully before you start

the product.

WARNING:

Keep your hands and feet

away from the rotating blades. Never

put your hands or feet close to or

under the product when the motor is

running.

WARNING:

Do not use the product

when persons, especially children, or

animals, are in the work area.

•

Set the

Main switch

in the

position to start

the product.

•

Set the

Main switch

in the

position when

the product is not in use or before any work,

inspection or maintenance is being carried

out.

When the

Main switch

is set in the

position

the motors on the product cannot start.

4.2 Start

Press the

STOP

button to open the hatch.

Set the main switch to position

Enter the PIN code.

Press the

START

button.

Select the desired operating mode. Refer to

Operating mode - Start on page 34

Close the hatch within 10 seconds.

If the product is parked in the charging

station, it will only leave the charging station

when the battery is fully charged and if the

timer is set to allow the product to operate.

Note:

Always press the

START

button before

closing the hatch to start the product. If the

START

button is not pressed, a message beep is

heard and the product will not start.

4.3 Operating mode - Start

When the

START

button has been pushed the

following operation selections can be selected.

•

Main area

•

Secondary area

•

Override timer

•

Spot cutting

4.3.1 Main area

Main area

is the standard operating mode where

the product mows and charges automatically.

4.3.2 Secondary area

In the

Secondary area

mode, the product

operates until the battery is empty.

When the battery is empty, the product stops and

the message

Needs manual charging

shows in

the product display. Put the product in the

charging station to charge the battery.

If the product charges in the

Secondary area

mode, it will fully charge, move out about 50 cm /

20 in. and then stop. This means that the product

is charged and prepared to start to cut.

- Operation

1220 - 001 - 08.07.2019