Husqvarna AUTOMOWER 310 Owner Manual - Page 32

To enable the GeoFence function

GeoFence is a GPS-based theft protection that

makes a virtual fence for the product. You will get

a message if the product is moved on the other

side of the GeoFence.

1.

Put the product in the center of the work

area.

2.

Do steps 1–3 in

To get access to the menu

on page 23

.

3.

Use the

arrow buttons

and the

OK

button to

move through the menu structure

Accessories > Automower Connect >

GeoFence > Activate GeoFence

.

4.

Push the

OK

button.

5.

Select

Activate GeoFence

and push the

OK

button.

To set a new center point for the Geofence

function

1.

Put the product in the center of the work

area.

2.

Do steps 1–3 in


on page 23

.

3.

Use the

arrow buttons

and the

OK

button to



GeoFence > New center point

.

4.

Push the

OK

button.

To set the GeoFence level of sensitivity

The higher level of GeoFence sensitivity, the

easier the alarm starts.

1.

Do steps 1–3 in


on page 23

.

2.

Use the

arrow buttons

and the

OK

button to



GeoFence

.

3.

Use the

arrow buttons

to select level of

GeoFence sensitivity.

4.

Push the

BACK

button.

To use the SMS function

The SMS function sends you an SMS when the

product is moved out of the GeoFence.

1.

Do steps 1–3 in


on page 23

.

2.

Use the

arrow

buttons and the

OK

button to



Communication > Use SMS

.

3.

Push the

OK

button.

4.

Use the

arrow

buttons and the

OK

button to



Communication > SMS phone numbers

.

5.

Push the

number

buttons to enter the

telephone number with country code. For

example (+)46701234567.

6.

Push the

BACK

button.

Note:

There is a maximum of 10 SMS each

month from the product.

Network

APN settings

The product must specify APN settings to be able

to use and send data via the mobile net. Settings

for Husqvarna SIM is default.

3.9.11.5 Headlights

To set the schedule for the headlights

1.

Do steps 1–3 in


on page 23

.

2.

Use the

arrow

buttons and the

OK

button to


Accessories > Headlights > Schedule

.

3.

Select between

Always ON, Evening only,

Evening & night

or

Always OFF

.

Note:

Evening only

will start the schedule for the

headlights at sunset and stop at midnight.

Evening & night

will start the schedule for the

headlights at sunset and stop at sunrise.

To set the Flashes when fault function

The headlights flashes if the product stops to

operate because of a fault if

Flashes when fault

is

enabled.

1.

Do steps 1–3 in


on page 23

.

2.

Use the

arrow

buttons and the

OK

button to


Accessories > Headlights > Flashes when

fault

.

3.

Use the

OK

button to enable or disable the

Flashes when fault

function.

32

- Installation

1220 - 001 - 08.07.2019

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	6
Symbols on the battery	6
Menu structure overview - 1	8
Menu structure overview - 2	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To set the corridor width of the boundary wire	19
To examine where to put the guide wire	19
To set the corridor width of the guide wire	20
Work area examples	20
Installation of the product	21
To install the charging station	21
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
To do the product settings	23
To get access to the menu	23
To do the timer settings	23
To calculate the timer setting	23
To set the timer	24
To copy the timer setting	24
To reset the timer setting	24
Security level	24
To set the security level	24
To change the PIN-code	25
To change the length of the alarm	25
To change the length of the time lock	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Lawn Coverage	25
To disable the GPS Assisted Navigation	26
To enable the GPS Assisted Navigation	26
To set the Lawn coverage function	26
To do a test of the Lawn coverage function	27
To measure the distance from the charging station	27
To disable or enable the Lawn coverage function	27
To reset the Lawn coverage settings	27
Methods for the product to find the charging station	27
To set how the product finds the charging station	27
To do a test of the guide wire	28
To do a test of the boundary wire	28
To change the signal range of the charging station	28
To set the exit angles	28
To set the reversing distance	28
To set the Drive Past Wire function	29
Settings	29
Profiles	29
To save settings to a profile	29
To change the name of a profile	29
To use a profile	29
To connect a new charging station to a profile	29
ECO mode	29
Spiral Cutting	30
To set the level of Spiral Cutting	30
Slope control	30
To disable the Slope control	30
To set the time & date	30
To set the language	30
To set the country	30
To reset all user settings	30
The About menu	30
Accessories	31
Information	31
Automower® Connect app	31
To install the Automower® Connect app	31
Automower® Connect@Home (Automower® 310/315)	31
To pair Connect@Home and the product	31
To remove paired accounts	31
Automower® Connect	31
To pair Automower® Connect and the product	31
To enable the GeoFence function	32
To set a new center point for the Geofence function	32
To set the GeoFence level of sensitivity	32
To use the SMS function	32
Network	32
APN settings	32
Headlights	32
To set the schedule for the headlights	32
To set the Flashes when fault function	32
To avoid collisions with the mower house	33
Connectivity	33
Automower® Direct	33
To start to use Automower® Direct	33
Husqvarna Fleet Services™	33
To connect to the product with Husqvarna Fleet Services	33
Operation	34
Main switch	34
Start	34
Operating mode - Start	34
Main area	34
Secondary area	34
Override timer	35
Spot cutting (Automower® 315/315X)	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start on next timer	35
To stop the product	35
To switch off the product	35
Timer and Standby	35
Example 1	36
Example 2	36
To charge the battery	36
Adjust the cutting height	37
To adjust the cutting height	37
Maintenance	38
Introduction - maintenance	38
Clean the product	38
Chassis and blade disc	38
Chassis	38
Wheels	38
Cover	38
Charging station	38
Replace the blades	39
To replace the blades	39
Battery	39
Winter service	40
Troubleshooting	41
Introduction - troubleshooting	41
Fault messages	41
Information messages	46
Indicator lamp in the charging station	47
Symptoms	48
Find breaks in the loop wire	49
Transportation, storage and disposal	52
Transportation	52
Storage	52
Disposal	52
To remove the battery	52
Technical data	53
Technical data	53
Registered trademarks	55
Warranty	56
Warranty terms	56
Applicable to US/CA market	57
Supplier's Declaration of Conformity	57

Husqvarna AUTOMOWER 310 Owner Manual - Page 32

To enable the GeoFence function, To set a new center point for the Geofence function

Page 32 highlights