Invacare TDXSPREE-CG Owners Manual 2 - Page 25

Footplates and Front Rigging, Reaching, Leaning and, Bending - Forward

Get Invacare TDXSPREE-CG PDF manuals and user guides View all Invacare TDXSPREE-CG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

2 SAFETY Footplates and Front Rigging ƽ WARNING If the wheelchair dips forward and the footplates touch the ground while the wheelchair is in motion, please contact your dealer for an inspection and avoid use of the wheelchair if possible. Otherwise the user could be injured. ALWAYS maintain a minimum of 3-inches between bottom of the front riggings and the floor/ground while the wheelchair is in motion to ensure proper ground clearance. If necessary, adjust the front rigging height or tilt seat to achieve proper ground clearance. DO NOT use the footplates as a platform. When getting in or out of the wheelchair, make sure that the footplates are in the upward position or swing footrests towards the outside of the wheelchair. Reaching, Leaning and Bending - Forward . ƽ WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees. Proper positioning is essential for your safety. Improper positioning while leaning or bending could cause the wheelchair to tip forward onto anti-tippers. Engage motor locks and turn power off before reaching, leaning or bending only as far as your arm will extend without changing your sitting position. Position the casters so that they are extended away from the drive wheels and engage wheel locks/motor locks/clutches.  For this procedure, refer to FIGURE 3. FIGURE 3 Reaching, Leaning and Bending - Forward Part No 1149267 25 Invacare® TDX® SC, Invacare TDX Spree

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
2
SAFETY
Part No 1149267
25
Invacare® TDX® SC, Invacare TDX Spree
Footplates and Front Rigging
Reaching, Leaning and
Bending - Forward
.
Engage motor locks and turn power off before reaching, leaning or
bending only as far as your arm will extend without changing your sitting
position. Position the casters so that they are extended away from the
drive wheels and engage wheel locks/motor locks/clutches.
FIGURE 3
Reaching, Leaning and Bending - Forward
±
WARNING
If the wheelchair dips forward and the footplates touch the ground while the wheelchair is in motion, please contact your
dealer for an inspection and avoid use of the wheelchair if possible. Otherwise the user could be injured.
ALWAYS maintain a minimum of 3-inches between bottom of the front riggings and the floor/ground while the wheelchair
is in motion to ensure proper ground clearance. If necessary, adjust the front rigging height or tilt seat to achieve proper
ground clearance.
DO NOT use the footplates as a platform. When getting in or out of the wheelchair, make sure that the footplates are in
the upward position or swing footrests towards the outside of the wheelchair.
±
WARNING
DO NOT attempt to reach objects if you have to
move forward in the seat or pick them up from
the floor by reaching down between your knees.
Proper positioning is essential for your safety.
Improper positioning while leaning or bending
could cause the wheelchair to tip forward onto
anti-tippers.
For this procedure, refer to FIGURE 3.