Invacare TDXSPREE-CG Owners Manual 2 - Page 64

CLOSED, Position, UP/OPEN

Get Invacare TDXSPREE-CG PDF manuals and user guides View all Invacare TDXSPREE-CG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

5 WHEELCHAIR OPERATION Tilting the Seat Assembly Back 1. Place the wheelchair in a well ventilated area where work can be performed without risking damage to carpeting or floor covering. 2. If necessary, tilt seat back 20° to 25°. 3. Verify the joystick ON/OFF switch is in the OFF position and disconnect joystick cable. 4. Engage the motor release levers. Refer to Disengaging/Engaging Motor Lock Levers on page 60. 5. Remove front rigging. Refer to seating system owners manual. 6. Remove the two mounting screws and washers securing the seat frame plate to the front seat posts.  Seating system not shown. UP/OPEN Position 7. Firmly grasp the front edge of the seat assembly, slowly tilt the seat assembly back into the UP/OPEN position. 8. Remove prop rod from the clip located on the Formula CG frame and engage the prop rod end into the front seat post. 9. Gently allow weight of seat assembly to be supported by the prop rod.  Only leave the seat assembly in the UP/OPEN position while performing any necessary procedures. Always lower the seat assembly to the DOWN/CLOSED position when not servicing the wheelchair. Ensure the seat is locked in place before using. Mounting Screw DOWN/ CLOSED Position Seat Frame Plate Washer and Locknut Front Seat Post FIGURE 16 - Tilting the Seat Assembly - Wheelchairs without Latch Bar Only Invacare® TDX® SC, Invacare TDX Spree 64 Part No 1149267

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
5
WHEELCHAIR OPERATION
Invacare® TDX® SC, Invacare TDX Spree
64
Part No 1149267
Tilting the Seat Assembly Back
1.
Place the wheelchair in a well ventilated area where work can be performed without risking damage to carpeting or floor covering.
2.
If necessary, tilt seat back 20° to 25°.
3.
Verify the joystick ON/OFF switch is in the OFF position and disconnect joystick cable.
4.
Engage the motor release levers. Refer to Disengaging/Engaging
Motor Lock Levers
on page 60.
5.
Remove front rigging. Refer to seating system owners manual.
6.
Remove the two mounting screws and washers securing the seat
frame plate to the front seat posts.
7.
Firmly grasp the front edge of the seat assembly, slowly tilt the seat
assembly back into the UP/OPEN position.
8.
Remove prop rod from the clip located on the Formula CG frame
and engage the prop rod end into the front seat post.
9.
Gently allow weight of seat assembly to be supported by the prop
rod.
FIGURE 16
- Tilting the Seat Assembly - Wheelchairs without
Latch Bar Only
Only leave the seat assembly in the UP/OPEN
position while performing any necessary
procedures. Always lower the seat assembly to
the DOWN/CLOSED position when not servicing
the wheelchair. Ensure the seat is locked in place
before using.
Seat Frame
Plate
Mounting
Screw
Washer and Locknut
Front Seat Post
DOWN/
CLOSED
Position
UP/OPEN
Position
Seating system not shown.